Question about 1991 Peugeot 405

7 Answers

My heater blower on my peugeot expert is not working

Ihas just recently purchased a peugeot expert van1.9 deisel 1997 R plate and the heater/blower has stopped working . i have tried checking the fuse but with no plan of which fuse is which i'm not having much sucess. i've also tried to feed alive wire from the battery to the power on what i believe isthe blower but no success. i've tried testing all the live wires that seem to connect to the blower no success. i need areally easy to follow instructions on how to solve this problem, please note it is peugeot expert van 1.9 deisel 1997 on r plate. this was not in the category section

Posted by on

Ad

7 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hi, had same problem twice with my 98 expert , first time it was heater control board(the slider sends a varying voltage thru the thin green wire at the motor plug, to a semi conductor encased in an ally heatsink when checking motor operation check thick red wire for 12v, and thin green for 1.5-4.5v, depnding on slider movement, and thick green for earth conn) , second fault was overheated conns both at motor conn and at relay(mine was bright green cased one behind glovebox), Terry

Posted on Nov 09, 2009

  • 1 more comment 
  • Charlie Holford Jun 30, 2012

    If you connect a voltmeter on the heater plug between the Green/Yellow wire and the Green wire, you should (with the engine running) get between 0 and about 5 volts when you move the heater slider switch from left to right

  • richard7302
    richard7302 Oct 25, 2013

    Thought I also should add that in addition to my written post further down I did a little YouTube video for the Heater Blower on an Expert Van

  • richard7302
    richard7302 Oct 25, 2013

    http://www.youtube.com/watch?v=abyAFOs5C...

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have a peugeot expert mini bus van 1999 found out the heater blower not working. i removed the blower unit and tested the motor and it was ok.and the ploblem i found was there is no power going to the red wire that connects to the fan blower i checked the fuse box and as for as i know all is ok but i have no idea what fuse it is connected to because i have no diagramfor it and were to go from here

Posted on Aug 18, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 250 Answers

1 of 2 things i always come across, 1st thing is the slider switch, then the variable resistor.

Posted on Aug 16, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Agreed with above BUT FIRST check the RELAY


my heater blower on my peugeot expert is not worki - 11_2_2012_5_33_13_pm.jpg

Mine had simply FRIED because of a bad connector. Its eight pounds for a new one and wish I had tried it first before stripping down the dash and changing the heater controls.

For the benefit of doubt here is what the heater control looks like stripped out of a Peugeot Expert van.




Yes I pulled all the dash apart its notmy heater blower on my peugeot expert is not worki - 11_2_2012_5_38_52_pm.jpgout half hour


11_2_2012_5_38_52_pm.jpg

You will need a special screwdriver for this type of my heater blower on my peugeot expert is not worki - 11_2_2012_5_39_56_pm.jpge all the same. So once you have the tool you have access to all


11_2_2012_5_39_56_pm.jpg

Never got round to cleaning up the unit simply replaced with scrap yard second SO I will sell this part on ebay for about thirty pounds


11_2_2012_5_41_43_pm.jpg

Mine changed to black because they sold me a 40amp version

Dangerous Maybe - but will keep an eye on it. I think they only had a 40amp in stock.

But many thanks to the guys above who posted first because you got me on the right track to this one.

Richard

Posted on Nov 02, 2012

  • 2 more comments 
  • Colm Mac Sweeney Oct 14, 2013

    Richard, I tried to remove the heater control also, but it seems that there are spring loaded leads coming from it and I am afraid if I pull any harder, these will come out and I wont be able to get the control back in again ?. Am I right ?

  • richard7302
    richard7302 Oct 25, 2013

    They can be a bit fiddly to get back but I did pull mine to bits and with the help of a sturdy pair of pliers reattach them, Because my van is old I wasnt too fussy so I kind of butchered my way through it. But its all back and working now.

  • richard7302
    richard7302 Oct 25, 2013

    Our Video: http://www.youtube.com/watch?v=abyAFOs5C...

  • Jamie Webber
    Jamie Webber Mar 05, 2016

    Richard,

    Have you got a 'How to' like your excellent one, above on how to disconnect and remove the "Heater Control", please?

×

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Cheers for that. I had the same problem and it was indeed the relay.

Posted on Dec 21, 2012

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 1 Answer

I had same problem with my 1997 1.9D Expert. I took out the blower by removing 3 screws and disconnecting the 3 wire connector. I connected to a power source 12V: nothing happend. First thought was fan needs replacement. I decided to go more into the deep and took the plastic cover off by removing 1 screw. I found that 1 of the brushes was stuck in its holder. Therefore no contact came to the collector. I managed to get the brush moving again and problem solved :)

Posted on Nov 22, 2012

  • Carlos
    Carlos Mar 11, 2018

    Brushes stuck in the holder was also the problem in my Peugeot 306 HDI. After cleaning, lubricated the assembly. All went back together and into place in about half an hour.
    Sold the car 4 years later never had a glitch from the ventilator.

×

  • Level 1:

    An expert who has achieved level 1.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 2 Answers

When you don't have 0-4v voltage on thin green (sometimes thin white) wire on the fan plug, probably you have problem with control panel (slider). Replace Zener diode. you need 7,5V diode. For example BZX85C7V5 or BZX55C7V5. I think original is bigger one. I bought smaller and it works. It costs couple cents.
BTW, your original resistor looks different than this on the picture. I replaced it for stronger, but it wasn't necessary.
my heater blower on my peugeot expert is not worki - 20622955_10214199002873678_1337359531_o-eh5x4e30apfcrmhjqavclxpr-1-0.jpg

Posted on Aug 10, 2017

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 peugeot


check fuses to heater control and heater blower motor.if fuses okay thermostat could be faulty causing coolant system not to get hot operating temperature.

May 26, 2013 | Cars & Trucks

1 Answer

My heater airflow in peugeot 307 has stopped working


The motor has a diode pack of resistors built into it so either this is defective or the brushes in the motor are sticking ,the motor is under the passenger side dash on models with AC ,pull the cover down and with the engine running and the blower turned on thump it with your fist ,it often works .

Jan 31, 2013 | Peugeot 307 Cars & Trucks

2 Answers

Heater blower stopped working and would like to know where in the engine bay its located ? thanks


Have you checked the fuse first.

The fuse must be in the main fuse box. The position of the fuses is normally marked on the inside of the fuse box cover and also in the owner's handbook. If you don't come right with these, work your way through the fuses looking for a blown one. To ease your search the fan fuse it should be around 25 to 30 amps.

The blower is not in the engine bay proper. It is below the air inlet grille under the windscreen, Access may be through the heater/ventilator unit in front of the console.

Feb 09, 2011 | Peugeot 405 Cars & Trucks

1 Answer

My indicators have stopped working also the heater


If the the indicator light's illuminate ,when turned on ,the signal flasher is at fault .
Replace it.

Mar 07, 2010 | 1991 Peugeot 405

1 Answer

I try to kick my four wheel drive in but the light just flashes and my heater stops blowing


check 4WD fuse also fuse and relay to heater blower.if all is good remove and hotwire blower motor using jumper wires to battery.if blower motor dont work replace it.if it work you have a faulty blower switch or resistor bad.

Dec 29, 2009 | 1997 Chevrolet K1500

2 Answers

1997 Dodge ram 2500 deisel. Blower fan wont come on. replaced climate control module and fuse is ok. Is there an inline fuse or relay I'm missing?


if the fuse is ok your next step is to see if you have power at the heater fan switch,if you do then the next thing is the heater blower motor resister it is under the heater assembly,that is what gives you different speeds,
the last is test for power at blower motor to see if it is faulty

Nov 21, 2009 | 1997 Dodge Ram 2500 Club Cab

1 Answer

I have got a peugeot 406 1.9 gldt on an n plate


check the wiring to the heater motor and the reostat, they are known for the connectors melting. also the reostat may be blown (the reostat is a number of resistors that control the fan speed)

Apr 09, 2009 | 1991 Peugeot 405

1 Answer

Peugeot 106 blown lights


u changed the bulbs? blower, when not working try and tap it, i think it will work as i think your car is high milleage and brushes are worn in the blower, it is under glove box.

Feb 28, 2009 | 2005 Peugeot 405

Not finding what you are looking for?
1991 Peugeot 405 Logo

24,730 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

scj103

Level 2 Expert

104 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...