Fuel pump located

SOURCE: I need to replace the fuel pump in my 1985 Chevy S10 Pickup.

EXACT PROCEDURE ! Please Rate Me Fairly for this!! Thank you And Good Luck !!


ELECTRIC PUMP

REMOVAL

1. Before servicing the fuel pump the fuel system pressure must be relieved. See: Fuel Pressure Release
2. Disconnect the negative battery cable.
3. Raise the car on a hoist.
4. Remove the fuel tank. See Fuel Tank / Service and Repair.
5. Remove the fuel tank sending unit and pump assembly by turning the cam lock ring counterclockwise. Lift assembly from the fuel tank.
6. Pull the fuel pump up into the attaching hose while pulling outward away from the bottom support. Take care to prevent damage to the rubber insulator and strainer during removal. After the pump assembly is clear of the bottom support, pull the pump assembly out of the rubber connector for removal. NOTE: Inspect the fuel pump attaching hose for any signs of deterioration. Also check the rubber sound insulator at the bottom of the pump. Replace damaged or deteriorated parts.

1. Push the fuel pump assembly into the attaching hose.
2. Position the fuel tank sending unit and pump assembly into the fuel tank. Use a new "O" ring seal. NOTE: Care should be taken not to fold over or twist the strainer when installing the sending unit as this will restrict the flow of fuel. Also, verify that the strainer does not block the full travel of the float arm.
3. Install cam lock over the assembly and lock by turning clockwise.
4. Reinstall fuel tank.

1. Disconnect fuel lines from fuel pump.
2. Remove fuel pump mounting bolts and the fuel pump.
3. Remove all gasket material from the pump and block gasket surfaces. Apply sealer to both sides of new gasket.
4. Position gasket on pump flange and hold pump in position against its mounting surface. Make sure rocker arm is riding on camshaft eccentric.
5. Press pump tight against its mounting. Install retaining screws and tighten them alternately.
6. Connect fuel lines. Then operate engine and check for leaks.

SOURCE: need relay location for electric fuel pump on 1991

under the hood or dash

SOURCE: location of fuel pump relay on 1994 s-10 pickup

Hello skaterkid012: My name is Roger and I will help you. You will find the fuel pump relay located under the center the center of the dash in the convenience center. Should you need further help please just ask. Please rate the answer you received.This way we know the answer was helpful. Thank You for using Fix Ya. Roger.

ZJ Limited

• 17989 Answers
• Posted on Apr 25, 2010

SOURCE: replace a fuel pump on 2000 chevy cavalier

REMOVAL & INSTALLATION
(see Figures 1 and 2)

CAUTION The fuel injection system remains under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.

1. Relieve the fuel system pressure using the recommended procedure.
2. Disconnect the negative battery cable.
3. Drain the fuel tank, then remove the fuel tank from the vehicle.
4. While holding the modular fuel sender assembly down, remove the snap-ring from the designated slots located on the retainer.

1. Remove the external fuel strainer.
2. Detach the Connector Position Assurance (CPA) piece from the electrical connector and detach the fuel pump electrical connector.
3. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tabs in the same manner.
4. Lift the cover assembly out far enough to detach the fuel pump electrical connection.
5. Rotate the fuel pump baffle counterclockwise and remove the baffle and pump assembly from the retainer.
6. Slide the fuel pump outlet out of slot, then remove the fuel pump outlet seal.

1. Install the fuel pump outlet seal, then slide the fuel pump outlet in the slots of reservoir cover.
2. Install the fuel pump and baffle assembly onto the reservoir retainer and rotate clockwise until seated.
3. Install the lower retainer assembly partially into the reservoir. Line up all 3 sleeve tabs. Press the retainer onto the reservoir making sure all 3 tabs are firmly seated.

1. Attach the fuel pump connector.
2. Fasten the CPA connector to the fuel sender cover.
3. Install a new external fuel strainer.
4. Install the modular fuel sender.
5. Install the fuel tank in the vehicle.
6. Connect the negative battery cable.
7. Pressurize the fuel system and verify no leaks.

SOURCE: 1997 S-10 Pickup: 97 chevy s 10 truck fuel gauge not working what co...

im not an expert but my chevy s-10s fuel gauge didnt work for like a year! and my fuel pump just went like a month ago replaced it and voila i have a fuel gauge again!