Both windows are screwed! What can I do to troubleshoot it? ...Please..? :)

Thought there were 2 big phillips head screws that held the handle on,from the bottom,also ,check the wiring inside the rubber boot,between the door and the body,just slit it with a razor blade,wires tend to break in there.

Hello,
Please remove all screw covers from the door panel, then remove screws, carefully remove the door panel and disconnect the cables to the power windows and power locks before getting the panel away.
Thanks

Remove all screws around the outer edge of the door panel. Carefully pry off the decorative cover behind the door handle and remove the torix screw. Lift up firmly on the door panel to remove. To reinstall, line up molded plastic hooks on back of door panel with notches in the door, push down to secure, reinstall torix screw, decorative cover and screws.
Also before you lift away the panel, you'll need to undo the electrical connectors for the power window and door locks

It is best to get the whole power window regulator assembly from the junkyard, which includes the power window motor. Cost should be no more than $40. Remove interior door trim panel by removing all screws and pulling up on the door panel. Unbolt existing window regulator assembly and slide guides from aluminum window track (you will have to uncrimp one end of track). Installation is the reverse of removal (remember to recrimp aluminum window track after reassembly). I did this repair in 45 minutes, power window worked like new. Good Luck!

Check to see if you have current going into and out of the power master switch on the driver's door. Remove the one phillips head screw and lift it out. More often than not, if the driver's switch goes bad, neither window will work. If there is power going in, then check for power coming out. In my experience, most salvage yards require you to test it (if you locate one at a yard which should be VERY easy) before you leave. Only takes a minute to pull. Two phillips head screws on the bottom of the master switch. Separate it, and pull it loose.

Hope I've helped.

Power Window Motor: Service and Repair
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the window regulator from the door.
3. Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
4. Remove the power window motor from the window regulator.
INSTALLATION
1. Position the power window motor onto the window regulator.
2. Install and tighten the screws that secure the power window motor to the window regulator. Tighten the screws to 9 Nm (80 in. lbs.).
3. Install the window regulator onto the door.
4. Reconnect the battery negative cable.

There are two screws at the bottom of door panel. The panel...pull from bottom first out toward you. work your way up the edges. When door panel is lose lift up and the top will come lose. The window regulator and motor are as one. Check fuse block under hood on driver side.

1. Remove the armrest pad retaining screw.
2. Remove the retaining screw and washer from the trim panel upper corner.
3. Remove the door handle screw and pull off the handle.
4. If equipped with manual windows, remove the window regulator handle screw and pull off the handle and washer. On vehicles with power windows, remove the power window switch housing.
5. If equipped with manual door locks, remove the door lock control. On vehicles with power door locks, remove the power door lock switch housing.
6. On models with electric outside rear view mirrors, remove the power mirror switch housing.
7. Remove the retaining screw and washer from the trim panel lower corner.
8. Using a special door trim panel removal tool or a flat wood spatula, insert it carefully behind the panel and slide it along to find the push-pins. When you encounter a pin, pry the pin outward. Do this until all the pins are out. NEVER PULL ON THE PANEL TO REMOVE THE PINS!
9. Installation is the reverse of removal.

Please don't forget to rate.

I'll get the pics here in a sec....takes a little bit to load.

here is step by step instruction to remove your door panel. i am not sure if the picture are coming through so please forgive me on the images. please do not forget to rate and comment about your experience today wih fixya Front Door

1. On vehicles without power windows, place a soft cloth under the window regulator handle and pull upwards on the cloth to release the snapring. Remove the regulator handle and plate.
   

Using a taped prytool, carefully remove the bezel portion of the handle
Remove the bezel by pulling towards the tip of the handle
Remove any screw covers ...
... and extract any retaining screws from the door panel

1. Remove the screw from the inside handle and slide the handle forward. Disconnect and remove the handle from the control link.
   
2. On manual mirrors, remove the setting screw and knob. Tape the end of a thin flat-bladed tool and pry the retainer loose to remove the cover.
   
3. If equipped with power windows, remove the power window switch from the and armrest.
   
4. Remove the mounting screws and remove the armrest from the door panel. Remove the inside door handle bezel by pushing rearward.
   

Carefully pry the edge of the door panel around the outer edges, then remove the door panel
Once the door panel is removed, make sure to disconnect all wiring

1. Remove the door courtesy light by pulling outward. Disconnect the electrical wiring.
   
2. Remove the two screw caps and speaker cover(s). Remove six screws from the trim panel.
   
3. Remove the door pocket from the panel.
   
4. Tape the end of a thin bladed tool, then insert the tool between the door panel and door and pry the panel outward. Disconnect the electrical wiring after the panel is free and remove the panel from the vehicle.
   

To install:

1. Connect the electrical wiring, if equipped, and install the trim panel onto the door.
   
2. Secure the trim panel with the mounting screws, then install screw caps and speaker cover(s).
   
3. Install the door pocket.
   
4. Install the armrest and secure with the mounting screws. Install the power window switch as required.
   
5. Install the door courtesy lamp. Install the inside handle bezel.
   
6. Install the outside rear view mirror cover and retainer.
   
7. Connect the inside handle to the control link. Install the handle, slide it rearward and install the screw.
   
8. With the door window fully closed, install the window regulator and handle.
   

1. Remove the front door trim panel (23942) ; refer to Section 501-05 .
   • Peel back the watershield.

1. Remove the rear view mirror mounting hole cover (17K709).

1. Disconnect the power mirror electrical connector.

1. Remove the outside rear view mirror (17682).
   1. Remove the screws.
   1. Remove the outside rear view mirror.

please rate as fixya if this works for you.

You must remove the door trim panel, it is held on with screws and spring type clips, the screws will be hidden under trim covers that pop off, don't force it!! or you will end up with a ruined panel, about $450 to replace.