Question about 2007 Toyota Corolla S

1 Answer

P2716 code in 2007 Toyota Corolla

Check engine light came on in my car last night, code read P2716... Some websites say transmission shift solenoid others say bad PCM... Please help? The car also has 111,000 miles on it so no warranty! How much will this problem cost me?

Posted by on

  • theodore ritter
    theodore ritter Oct 05, 2017

    HELLO, THERE IS A RECALL STILL IN EFFECT FOR DEFECTIVE COMPUTERS FOR THIS CODE, PLEASE CONTACT A TOYOTA DEALER WITH YOUR VEHICLE INFORMATION, IF THE RECALL APPLIES YOU WILL GET THE ECM REPLACED AT NO CHARGE.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 992 Answers

P2716 -Pressure Control Solenoid "D" Electrical (Shift
Solenoid Valve SLT)
Trouble Area:
1. Open or short in shift solenoid valve SLT circuit. (repair harness wiring)
2. Shift solenoid valve SLT defective. (replace)
3. ECM defective. (replace with a good known one)

Posted on Dec 08, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Superbovine

  • 333 Answers

SOURCE: Pressure Control Solenoid D electrical fault (P2716)

There is a Bulletin on this concern, and it is a warrantable condition for 8 years or 80,000 miles so you are still covered by the factory warranty.
The problem is a logic issue in the PCM. The correction is a new PCM with updated software.


Reference bulletin #TC015-07

The contents are below:

TRANSMISSION & CLUTCH
TC015-07 Title:
HARSH SHIFT AND M.I.L. "ON"
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007

Introduction
Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored.
Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring.

Applicable Vehicles
^ 2005 - 2007 model year Corolla and Matrix (2WD) vehicles equipped with the 1ZZ-FE engine.
Warranty Information
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date.



** Please be sure to rate me if this free information has been helpful!

Posted on Sep 21, 2009

Testimonial: "Thank you so much!! "

Anonymous

  • 543 Answers

SOURCE: The indicator on my car says check engine, and the

they will work on your car its just not covered under warranty,,,

Posted on Oct 19, 2009

Superbovine

  • 333 Answers

SOURCE: p2716 pressure control solenoid d 2005 toyota

This is very common on Matrix/Corollas and is repairable by way of replacement PCM to correct invalid parameters. the labor is low but the part is very expensive.

Expect approximately $89 or less in labor, and $648 for the new PCM



Reference bulletin #TC015-07

The contents are below:

TRANSMISSION & CLUTCH
TC015-07 Title:
HARSH SHIFT AND M.I.L. "ON"
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007

Introduction
Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored.
Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring.

Applicable Vehicles
^ 2005 - 2007 model year Corolla and Matrix (2WD) vehicles equipped with the 1ZZ-FE engine.
Warranty Information
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date.

Posted on Oct 29, 2009

Danniboi

Dan Doherty

  • 1098 Answers

SOURCE: 2005 Toyota Corolla check engine light on.Fault

Hi
Could mean there is one fault causing many faults, example, Air mass sensor, this can cause rough idle and over fuelling so the code reader will just send it back with undefined as there are to many faults to identify as the cause.

Most likely it will be a air fault so check the air sensor first, try cleaning it with carb cleaner, sometimes works. If not get back to me could be 2 other things. although the car will not drive very well if it is any of the other 2.

Regards
Dan

Posted on Feb 10, 2010

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: I have a 2006 Toyota

DTC P2716 - Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

If you need to test this electrical components and wiring. Tell me if you need the TSB about this DTC.

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 chevy malibu damage Light front end damcodend error codes P0401 P0605 P0842 P0642 The 0401 code is being thrown twice and I belive it is the egr wich is common on these cars from what my buddy tells...


DTC P0401 Exhaust Gas Recirculation (EGR) Flow Insufficient
Probably plugged passage's , not the EGR valve .
What type code reader are you using to read these codes ? I have factory service info. Doesn't show P0842 or P0642 , no such codes . You don't show what engine yours has , I'am assuming you have 3.5 L !
P0604
Control Module Random Access Memory (RAM)
PCM
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610 in Engine Controls - 2.2L (L61)
or
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610 in Engine Controls - 3.5L (LX9)

P0717
Input Speed Sensor Circuit Low Voltage
PCM
DTC P0717 in Automatic Transaxle - 4T40-E/4T45-E
P0741
Torque Converter Clutch (TCC) System - Stuck Off
PCM
DTC P0741 in Automatic Transaxle - 4T40-E/4T45-E
P0742
Torque Converter Clutch (TCC) System - Stuck On
PCM
DTC P0742 in Automatic Transmission - 4T40-E/4T45-E
P0748
Pressure Control (PC) Solenoid Control Circuit
PCM
DTC P0748 in Automatic Transmission - 4T40-E/4T45-E
P0751
1-2 Shift Solenoid (SS) Valve Performance - No First or Fourth Gear
PCM
DTC P0751 in Automatic Transmission - 4T40-E/4T45-E
P0752
1-2 Shift Solenoid (SS) Valve Performance - No Second or Third Gear
PCM
DTC P0752 in Automatic Transmission - 4T40-E/4T45-E
P0753
1-2 Shift Solenoid (SS) Control Circuit
PCM
DTC P0753 in Automatic Transmission - 4T40-E/4T45-E
P0756
2-3 Shift Solenoid (SS) Valve Performance - No First or Second Gear
PCM
DTC P0756 in Automatic Transmission - 4T40-E/4T45-E
P0757
2-3 Shift Solenoid (SS) Valve Performance - No Third or Fourth Gear
PCM
DTC P0757 in Automatic Transmission - 4T40-E/4T45-E
P0758
2-3 Shift Solenoid (SS) Control Circuit
PCM
DTC P0758 in Automatic Transmission - 4T40-E/4T45-E
P0815
Upshift Switch Circuit
PCM
DTC P0815 in Automatic Transmission - 4T40-E/4T45-E
P0816
Downshift Switch Circuit
PCM
DTC P0816 in Automatic Transmission - 4T40-E/4T45-E
P0826
Up and Down Shift Switch Circuit
PCM
DTC P0826 in Automatic Transmission - 4T40-E/4T45-E
P0973
1-2 Shift Solenoid (SS) Control Circuit Low Voltage
PCM
DTC P0973 in Automatic Transmission - 4T40-E/4T45-E
P0974
1-2 Shift Solenoid (SS) Control Circuit High Voltage
PCM
DTC P0974 in Automatic Transmission - 4T40-E/4T45-E
P0976
2-3 Shift Solenoid (SS) Control Circuit Low Voltage
PCM
DTC P0976 in Automatic Transmission - 4T40-E/4T45-E
P0977
2-3 Shift Solenoid (SS) Control Circuit High Voltage
PCM
DTC P0977 in Automatic Transmission - 4T40-E/4T45-E

Sometimes with code readers they get confused an just throw any old codes . Have it checked by someone with GM Tech 2 scan tool .

Aug 03, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

Toyota hilux 2011 model trouble code p2716


here is some info. I hope it helps.

This is a code relative to shift solenoid malfunctions in your computer. This is a known problem on your model and Toyota released an updated PCM to correct the problem.
While you can replace the PCM yourself if you are out of warranty, your dealer will need to code your VIN to it in order to get rid of the check engine light.
The warranty coverage is 8 years or 80,000 miles from new.

The details of the bulletin are below:

TRANSMISSION & CLUTCH
TC015-07 Title:
HARSH SHIFT AND M.I.L. "ON"
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007
TSB UPDATE NOTICE:The information contained in this TSB supercedes TSB No. TC014-06.
TSB No. TCO14-06 is now obsolete and should be discarded. Introduction
Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored. Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring

Aug 30, 2015 | Toyota Cars & Trucks

2 Answers

03 Toyota 4runner 4wd 4.7l had codes p0771 , p0986, and p2716 with vsc light on. Told to replace trans. Replaced with used and now has p0778 and p2716 now with vsc light on and still harsh shifts


Who told u to replace trans?..first thing should have been done was check wiring and connections at transmission and ECM and between the 2...also need to check the pressure control solenoids B and D...its possible the ECM is acting up especially since P2716 came back twice.

Mar 08, 2015 | Toyota Cars & Trucks

2 Answers

I got a 2005 pontiac vibe cant not get no one to know how to fix it. Pressure Control Solenoid code p2716 keep poping up when i get it looked at . I want to know if i can get info on where to buy it. ...


If no one has been able to find the issue with this.It is possible that the pcm may be having an issue of sorts and may need replaced. There are a few tests that should be run prior to condemning the vehicles computer. Info yyou would like the testing info let me know but fully capable a scan tool is required for a portion of testing.



Circuit Description
The throttle pressure that is applied to the primary regulator valve modulates the line pressure causing the line pressure solenoid valve to precisely modulate and create line pressure according to throttle position or engine load. This modulation action controls the line pressure which in turn provides smoother shifts between gears.
When the powertrain control module (PCM) receives the throttle position opening angle, the PCM controls the line pressure by sending a predetermined duty cycle to the solenoid valve.
The line pressure solenoid valve controls the transaxle line pressure for smooth transaxle operation based on signals from the throttle position (TP) sensor and the vehicle speed sensor (VSS).
When the PCM detects a continuous open or short to ground in the line pressure solenoid circuit, then DTC P2716 sets.
DTC P2716 is a type B DTC.
DTC DescriptorThis diagnostic procedure supports the following DTC:
DTC P2716 Line Pressure Control Solenoid
Conditions for Running the DTCPCM detects a open or short to ground in line pressure solenoid circuit.
Conditions for Setting the DTCDTC P2716 sets when either of the following conditions occurs:
• The PCM detects an open in the solenoid circuit. • The PCM detects an short to ground in the solenoid circuit. Action Taken When the DTC Sets • At the time of the first failure, the PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as a Failure Record. • The PCM illuminates the malfunction indicator lamp (MIL) during the first consecutive failure in which the Conditions for Setting the DTC are met. • The PCM turns OFF power to the solenoid. • The PCM stores DTC P2716 in PCM history. Conditions for Clearing the MIL/DTC • A scan tool can clear the MIL/DTC. • The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission related diagnostic fault occurring.

Apr 23, 2011 | 2005 Pontiac Vibe

1 Answer

Pressure Control Solenoid P2716


have the code checked especially if the car is out of warranty. If it is still under warranty take the car to the dealership . The Pressure Control Solenoid determines the quality and accuracy of the shift points and if you let it go the transmission will not shift properly after a period of time. The pressure control solenoid is used by the PCM to raise the mainline hydraulic pressure during high throttle - this increases the holding force on the clutches and bands and prevents slipping. The pressure control solenoid is controlled by pulses from the PCM and this in turn operates the boost valve insde the valve body.

The problem could be either in the PCM or it could be an electrical problem with the solenoid. As suggested it should be diagnosed by a transmission tech. They can check if the PCM is good by looking at the pulses with an oscilloscope at the connector and they should also be able to test the continuity of the solenoid. If the solenoid is faulty the valve body will need to be removed and the solenoid replaced.
good luck

Apr 04, 2010 | 2006 Pontiac Vibe

2 Answers

P2716 pressure control solenoid d 2005 toyota corolla 117000 miles check engine light on


This is very common on Matrix/Corollas and is repairable by way of replacement PCM to correct invalid parameters. the labor is low but the part is very expensive.

Expect approximately $89 or less in labor, and $648 for the new PCM



Reference bulletin #TC015-07

The contents are below:

TRANSMISSION & CLUTCH
TC015-07 Title:
HARSH SHIFT AND M.I.L. "ON"
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007

Introduction
Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored.
Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring.

Applicable Vehicles
^ 2005 - 2007 model year Corolla and Matrix (2WD) vehicles equipped with the 1ZZ-FE engine.
Warranty Information
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date.

Oct 28, 2009 | 2006 Toyota Matrix

2 Answers

Pressure Control Solenoid D electrical fault (P2716)


There is a Bulletin on this concern, and it is a warrantable condition for 8 years or 80,000 miles so you are still covered by the factory warranty.
The problem is a logic issue in the PCM. The correction is a new PCM with updated software.


Reference bulletin #TC015-07

The contents are below:

TRANSMISSION & CLUTCH
TC015-07 Title:
HARSH SHIFT AND M.I.L. "ON"
DTC P2716 Models:
'05 - '07 Corolla & Matrix (1ZZ-FE) September 20, 2007

Introduction
Some 2005 - 2007 model year Corolla and Matrix vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and a M.l.L. ON" with DTC P2716 stored.
Improvements have been made to the Engine Control Module (ECM) (SAE term:
Powertrain Control Module/PCM) to reduce the possibility of this condition occurring.

Applicable Vehicles
^ 2005 - 2007 model year Corolla and Matrix (2WD) vehicles equipped with the 1ZZ-FE engine.
Warranty Information
Applicable Warranty*:
This repair is covered under the Toyota Federal Emissions Warranty. This warranty is in effect for 96 months or 80,000 miles, whichever occurs first, from the vehicle's in-service date.



** Please be sure to rate me if this free information has been helpful!

Sep 21, 2009 | 2006 Toyota Matrix

4 Answers

Oem code p2716


Same issue.

There is a service bulletin on this. Toyota will replace computer. I have a 2007 Corolla S with 56,000 miles

Nov 01, 2008 | 2007 Toyota Corolla

Not finding what you are looking for?
2007 Toyota Corolla S Logo

1,700 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...