SOURCE: front grill on toyota solara
That is correct - it worked for me - now the questions is - How do I remove the old logo ?
SOURCE: What is the yellow warning light that looks like a
If it looks like this ( ! ) I believe it is the tire pressure symbol, check your owners manual for confirmation.
Inflate tires and see if that helps.
Shoot down to the mechanics who should have a code reader, he will be able to read and reset any error codes for you. Most mechanics won't charge for looking. Good luck
SOURCE: How to replace a starter on a toyota solara v6
You take out the battery, and the air-filter housing to give extra working space.
Then push in the starter motor to its place, and hand-tighten all its bolts.
Wrench tighten the starter bolts to the engine 38.ft-lb
Connect the solenoid wire, and tighten to 10.ft-lb
Connect the battery positive cable, and tighten to13.ft-lb.
Replace the air-filter housing.
Replace the battery, and terminals.
Crank-up the car.
SOURCE: program garage door opener on a 2006 toyota solara
GOTO HOMELINK.COM
THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.
PLEASE NOTE: MOST BUT NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.
HOPE THIS HELPS
Sit in back seat passenger side. Remove panel which is on top which is below rear window, same panel where seat belt goes into panel at top. You will need to remove #2 Phillips screws which hold panel in place. Screws are hiding behind seat belt front cover where belt goes down in panel, under cup holder which allows arm rest cover to lift off and one more right on left side of head rest in corner. Remove panel. You will see switch which is in vertical position. If for any reason you want to by-pass switch, just unplug switch. Radio will still work in standard mode. The amp sound will not increase in performance when top is down and sound will not be as sharp.
Rear iignts in rear na, removing and instaiiing
Fig. 325: Rear Lights In Rear Lid, Removing And Installing
Courtesy of VOLKSWAGEN UNITED STATES, INC.
Removing
CAUTiON: • Switch off all electrical components.
. . Switch ignition off and remove ignition key.
o Turn light switch into "0" position.
o Open cap - 1 - for warning triangle.
o Rotate quick-release screw - 2 - counter-clockwise 90 C
and remove cover - 3 - from luggage compartment lining - direction of arrow -
Fig. 326: Removing Bulb Socket From Housing, Pressing Catch
Bracket Downward
Courtesy of VOLKSWAGEN UNITED STATES, INC.
o Disconnect electrical harness connector
o Remove bulb socket - 1 - from housing, press catch bracket
- 2 - downward - arrow - to do so
Fig. 327: Identifying Nuts, Clamping Bracket, Inner Tail
Lamp, And Clamp Mounting
Courtesy of VOLKSWAGEN UNITED STATES, INC.
o Unscrew nut - 2 - and remove clamping bracket - 1 -
o Remove nut - 4 - and remove inner tail lamp - 3 - toward
outside
o Remove clamp mounting - 5 - from body cut-out
Fig. 328: Identifying Clamp Mounting, Nuts, Inner Tail Lamp,
And Tabs
Courtesy of VOLKSWAGEN UNITED STATES, INC.
Installing
Installation is the reverse of removal, noting the
following:
NOTE: • Make sure seal between body and tail lamp housing
seals properly.
. Attach clamp mounting -2 - at inner tail lamp and screw on
nut -3 - loosely.
. Attach inner tail lamp -4 - at body cut-out and make sure
grip tabs - arrows - of clamp mounting rest against body cut-out
. Slide clamp mounting - 1 - onto threaded pin of inner tail lamp and tighten nuts - 3 - and -5 -.
32 views
Usually answered in minutes!
×