P1739 general position encoder fault estoff light always on. vehicle accelerates very slowly is this a sensor i can check, actuator, solenoid mabey?where should i start

engine losing power sign ??? .You mean ENGINE POWER REDUCED ? This has to do with electronic throttle control -Throttle Actuator Control (TAC) System Description

The throttle actuator control (TAC) system is used to improve emissions, fuel economy, and driveability. The TAC system eliminates the mechanical link between the accelerator pedal and the throttle plate. The TAC system eliminates the need for a cruise control module and idle air control motor. The following is a list of TAC system components:
• The accelerator pedal assembly includes the following components:
- The accelerator pedal
- The accelerator pedal position (APP) sensor 1
- The APP sensor 2
• The throttle body assembly includes the following components:
- The throttle position (TP) sensor 1
- The TP sensor 2
- The throttle actuator motor
- The throttle plate
• The engine control module (ECM)

TAC System Default Actions/Reduce Power Modes
There are 2 reduce power modes that the engine control module (ECM) can default to if an error is detected in the throttle actuator control (TAC) system. If an accelerator pedal position (APP) sensor 1 or APP sensor 2 circuit fault, throttle position (TP) sensor 2 circuit fault, or if a TP sensor 1 circuit fault is detected with some APP angle, the ECM goes into one of the 2 reduce power modes. In this mode, the engine torque is limited so that the vehicle cannot reach speeds of more than 100 km/h (60 mph). The ECM remains in this reduce power mode during the entire ignition cycle even if the fault is corrected.
If there is a condition with the throttle actuator control circuits, throttle actuator command vs actual position fault, return spring check fault, or a TP sensor 1 circuit fault, the ECM goes into the other reduce engine power mode. In this mode, the engine speed is limited to 2,500 RPM and the 3-6 fuel injectors are randomly turned OFF. At this time the Reduced Power indicator is commanded ON. The ECM remains in the reduce power mode during the entire ignition cycle even if the fault is corrected. Observe, if a TP sensor 1 or throttle actuator control circuit fault is present at the time the vehicle is at idle, with no accelerator pedal angle, the engine may stall.
© 2022 General Motors Corporation. All rights reserved.

You need to have a qualified repair shop check it out.

Sorry , no reset for the fuel pump . Reduced engine power message is for the TAC - throttle actuator control system . Electronic throttle control . Reduced Engine Power: Throttle Actuator Control (TAC) System Description for the 3.6L engine or Throttle Actuator Control (TAC) System Description.TAC System Default Actions/Reduce Power Modes
There are 2 reduce power modes that the engine control module (ECM) can default to if an error is detected in the throttle actuator control (TAC) system. If an accelerator pedal position (APP) sensor 1 or APP sensor 2 circuit fault, throttle position (TP) sensor 2 circuit fault, or if a TP sensor 1 circuit fault is detected with some APP angle, the ECM goes into one of the 2 reduce power modes. In this mode, the engine torque is limited so that the vehicle cannot reach speeds of more than 100 km/h (60 mph). The ECM remains in this reduce power mode during the entire ignition cycle even if the fault is corrected.
If there is a condition with the throttle actuator control circuits, throttle actuator command vs actual position fault, return spring check fault, or a TP sensor 1 circuit fault, the ECM goes into the other reduce engine power mode. In this mode, the engine speed is limited to 2,500 RPM and the 3-6 fuel injectors are randomly turned OFF. At this time the Reduced Power indicator is commanded ON. The ECM remains in the reduce power mode during the entire ignition cycle even if the fault is corrected. Observe, if a TP sensor 1 or throttle actuator control circuit fault is present at the time the vehicle is at idle, with no accelerator pedal angle, the engine may stall.

there's a website reliable-store
all heavy equipment repair issues servicing, loading, wiring, engine problems everything is covered here its a must try

Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).

?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

Reduced Engine Power
Refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 3.6L or Throttle Actuator Control (TAC) System Description in Engine Controls - 3.8L
TAC System Default Actions/Reduce Power Modes
There are 2 reduce power modes that the engine control module (ECM) can default to if an error is detected in the throttle actuator control (TAC) system. If an accelerator pedal position (APP) sensor 1 or APP sensor 2 circuit fault, throttle position (TP) sensor 2 circuit fault, or if a TP sensor 1 circuit fault is detected with some APP angle, the ECM goes into one of the 2 reduce power modes. In this mode, the engine torque is limited so that the vehicle cannot reach speeds of more than 100 km/h (60 mph). The ECM remains in this reduce power mode during the entire ignition cycle even if the fault is corrected.
If there is a condition with the throttle actuator control circuits, throttle actuator command vs actual position fault, return spring check fault, or a TP sensor 1 circuit fault, the ECM goes into the other reduce engine power mode. In this mode, the engine speed is limited to 2,500 RPM and the 3-6 fuel injectors are randomly turned OFF. At this time the Reduced Power indicator is commanded ON. The ECM remains in the reduce power mode during the entire ignition cycle even if the fault is corrected. Observe, if a TP sensor 1 or throttle actuator control circuit fault is present at the time the vehicle is at idle, with no accelerator pedal angle, the engine may stall.

Possible causes Faulty Accelerator Pedal Position Sensor
Accelerator Pedal Position Sensor harness is open or shorted
Accelerator Pedal Position Sensor circuit poor electrical connection
Faulty Electric Throttle Control Actuator


Read more: http://engine-codes.com/p2138_chevrolet.html#ixzz3OUJO7vFr

first code it's P0320 Possible causes
- Faulty Ignition/Distributor engine speed sensor
- Faulty Crankshaft Position sensor
- Ignition/Distributor engine speed sensor harness is open or shorted
- Ignition/Distributor engine speed sensor circuit poor electrical connection
- Low battery charge
- Faulty Engine Control Module (ECM)


Read more: http://engine-codes.com/p0320_ford.html#ixzz3DcwddSlp
2- P0750 Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 1 valve
- Shift solenoid 1 valve harness or connectors
- Shift solenoid 1 valve circuit is open or shorted


Read more: http://engine-codes.com/p0750_ford.html#ixzz3DcwoXS73
3- P0120 Possible causes
- Faulty Throttle Position Sensor
- Throttle Position Sensor circuit is open or shorted
- Throttle Position Sensor poor electrical connection


Read more: http://engine-codes.com/p0120.html#ixzz3Dcx3VCPs
4- P0220 Possible causes
- Throttle Position Sensor (TPS) harness is open or shorted
- Throttle Position Sensor (TPS) circuit poor electrical connection
- Faulty Throttle Position Sensor (TPS)
- Fault Electric Throttle Control Actuator (or Throttle Body Motor)
- Accelerator Pedal Position Sensor (APP)


Read more: http://engine-codes.com/p0220.html#ixzz3DcxGUMl4

No messaage of reduced engine power ? Your vehicle has electronic throttle control . Has four position sensors , two are located in the gas pedal ,an two in the throttle body . The PCM uses these sensor to know how much to open the throttle plate ,allowing more air into the engine . How did you read this code an where did you read it's definition at ? This is not a code for your vehicle . Some time cheap code readers get them wrong .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit
DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage
DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage
DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit
DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage
DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage
DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

DTC P1516: Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance
DTC P2101: Throttle Actuator Position Performance
DTC P2119: Throttle Closed Position Performance
DTC P2176: Minimum Throttle Position Not Learned

If one of this position sensors is bad it will throw the PCM into a
Reduced Engine Power Mode
When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
• Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control; however, the vehicle acceleration is limited.
• Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control; however, the maximum throttle opening is limited.
• Throttle default mode--The ECM will turn off the throttle actuator motor and the throttle will return to the spring loaded default position.
• Forced idle mode--The ECM will perform the following actions:
- Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned off.
- Ignore the accelerator pedal input.
• Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.


017 Accelerator Pedal Position Sensors
Drive by Wire Function and diagnostics by Wells

P1728 EMC-Open/Short To Battery P1739 General Position Encoder Fault I would try to clear the faults with a scan tool. If they return take to the dealer for a more detailed fault analysis.

Code PO10 has to do with the "Camshaft Position Actuator circuit Bank 1" an actuator is a relay,solenoid or motor that send a signal to the cumputer that something is wrong.i think in this case it is the Camshaft Position Sensor or the camshaft interrupter magnet. Probably the sensor has to be replaced. It is located on the engine block.