Fuse controls dashboard lights

If your Nissan Cabster 1.5 tonne truck is experiencing no dashboard lights and rear lights, there are a few potential causes for this issue:

1. Blown fuses: The dashboard and rear lights are connected to separate fuses. A blown fuse could cause one or both of these lights to stop working. Check the fuse box and replace any blown fuses.
2. Wiring issue: A wiring problem such as a broken wire or loose connection may prevent power from reaching the lights.
3. Switch problem: The problem could be the switch controlling the lights. The switch may be worn out or malfunctioning, preventing the lights from turning on.
4. Bulb problem: The dashboard and rear lights are controlled by separate bulbs. One or both of the bulbs may be burned out or damaged.
5. Electrical module problem: Some vehicles have an electrical module that controls the lights; if the module is faulty, it can cause the lights not to work.

It's best to have a professional technician diagnose the issue. They will be able to identify the specific cause of the problem and make the necessary repairs. It's also important to check the owner's manual for troubleshooting options or error codes that might be displayed on the dashboard.
It's also important to note that the lack of dashboard and rear lights can affect the safety of the vehicle and the driver; thus, it is vital to have it fixed as soon as possible.

If all the lights on your dash seem to be off, the problem could be a bad fuse.

Locate the knob por dial that control the brightness of dashboard light.

Make sure the brightness control is turned on. If it is and the lights aren't working, the problemas may be a bad fuse.

Use your car manual and locate the dash fuse the fuse box is between under the steering wheel and the door. Pull out the fuse and use a test light by connecting the groud clamp to the metal and placing the other end where the fuse was. If the light come on, you need to replace the fuse.

Dashboard backlight works together with the tail light. Both the headlight and tail light is controlled by relays. Check the engine bay fusebox. Look at the inside of the fusebox cover and you can see the 'location map'of relays and fuses. Theheadlight and tail light relays sits side-by-side. Change both and check for blown hedlight fuses..

Should be in the fuse block under the dashboard by the driver side kick panel (lighting or illumination)if ok try adjusting the brightness control.

When the dashboard lights in your vehicle malfunction or cease to operate, the resulting effects can range from being a mere annoyance to posing a safety hazard. Locating the problem and finding a remedy is essential. To fix dashboard lights that won't light, follow these suggestions

Evaluate the problem methodically. Begin the process by trying the simplest of solutions first. Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column, make sure its in the correct position to have the lights on.

Check the dashboard light fuse. A blown fuse can disable the vehicle's dashboard light. The fuse box may be under the hood, or on the floor, near the brake pedal, or there may be 2 fuse boxes in both places. Refer to the diagram on the fuse box cover to locate the correct fuse. Replace the dashboard light fuse if necessary.

If all of the above don't fix it, then replace your light switch.

sounds like you may be haveing issues with blower motor its trying to go out all together

Locate the knob or dial that controls the brightness of the dashboard lights. If the control is not immediately evident, check your owner's manual.

2 Make sure the brightness control is turned on. If it is and the lights aren't working, the problem may be a bad fuse.

3 Check the fuse that controls the dashboard lights (see How to Fix a Faulty Car Fuse). Replace the fuse if necessary.

Locate the knob or dial that controls the brightness of the dashboard lights. If the control is not immediately evident, check your owner's manual.

Make sure the brightness control is turned on. If it is and the lights aren't working, the problem may be a bad fuse.

Check the fuse that controls the dashboard lights. Replace the fuse if necessary.

Call your mechanic if neither of these steps fixes your problem.

illumination

either a wiring problem or a circuit board problem from behind the clocks.there are 2 type of clocks for this specific model.any reputable bm breakers can sell u 1 4 30-40quid.it will take 5mins to do all u need is a torquescrewdriver.2 small screws at top of clocks just under the top of dash

for the dashboard... have you checked the intensity control? It happened to a friend of mine.