Replaced timing belt,distributor cap,crank shaft position scensor,spark plugs,its in time
Dude, I have the dealers official repair manual, shot me an email at [email protected] and I will email it to you in a PDF file, Free
Try this:
Check the battery like this:
Turn on the headlights, then try to start the car.
If the headlights do not dim or go out, then the battery is likely ok.
Check that the battery cable plus post, goes to the starter, Minus post to a good ground, like the engine.
If wiring is ok, then look at the starter solenoid for a good connection, and proper voltage at the starter.
Problem is most likely the Solenoid's bendix gear or starting relay, Have someone bang on the starter while you try to start the car. This usually works by dislodging the bendix gear..
Hope this helps.
I would do a once over. Make sure your timing belt is installed in the correct pos. I would also make sure your distributor is installed correctly, off one gear and it won't start. Make sure the wires are on the correct post and plugs. Good luck
SOURCE: changed timing belt 94 civic ex 1.6, now wont start
first make shure the fireing order is correct 1 3 4 2, make shure you have the timeing set right
SOURCE: 1991 Honda Civic STILL won't start
if your not getting spark then your coil is the mostlikely cause it's obviously not a timing issue since you stated that the rotor is spinning. if the spark plugs are bad then replace them too . to be sure that your getting spark to all cylinders test each of the spark plugs after replacing the coil. just to besure it's not starving for fuel as well spray a little ether in the breather if it fires off right away that means the even though your fuel pump works it may not have a high enough pressure. let me know the results
SOURCE: 1995 honda civic d15b7 cranks but wont start. new
Are you sure you have correct timing? its definetly a fule problem, if timing is good then turn your key to the on position and try to listin for the fule pump to prime. While the key is in on position go to fuel rail, there is a valve on fule rail called sharader valve. Get a small screw driver and press valve in to check if car has fule pressure. if pressure is present then it is incorrect timing or possible bad cam sensor.
SOURCE: 2001 honda civic ex,wont start, no injector pulse,
Injector pulses are sent from the engines computer. Have that checked out
SOURCE: my honda oddessey 1995, my
Hi, since you've replaced everything else, about the only thing left is the crankshaft position sensor. This is the sensor the computer uses to time the spark signals. Because this sensor is expensive, I recommend you test it first to verify it's bad before replacing. I have pasted test procedures below as well as replacement procedure in case it fails the tests. You will need an ohmmeter for the test. If you don't have an ohmmeter, you can buy one for as little as $10, or maybe you can borrow one. You will also need a timing light if you replace the sensor. Please let me know if you have questions, and thanks for using FixYa. Fig. Fig. 2: The Crankshaft Position (CKP) Sensor rotor looks like a small gear in the lower distributor housing- CRV and 1995 Odyssey models 7. Check and reset the ignition timing as outlined below. Fig. Fig. 1: The inductive lead of the timing light is placed around the No. 1 spark plug wire; and the light is aimed toward the marks on the crankshaft pulley. Fig. Fig. 2: The red ignition timing mark on the crankshaft pulley is lined up with the pointer. The two small notches on either side of the red colored notch represent the plus (+) or minus (-) 2Ā° increments. The white notch to the far right is Top Dead Center (TDC)
TESTING CRV and 1995 Odyssey Models
CRV models: The blue and white wires. The resistance should be 300-700 ohms.
1995 Odyssey models: The blue/green and blue/yellow wires. The resistance should be 700-1,300 ohms.
REMOVAL & INSTALLATION CRV and 1995 Odyssey Models
To install:
ADJUSTMENT CRV and 4-Cylinder Odyssey Models
If equipped with an automatic transaxle, place the shifter in Park or Neutral. If equipped with a manual transaxle place the shifter in Neutral. Make sure to apply the parking brake and block the drive wheels.
Odyssey models with 4-cylinder engines: centrally located on the passenger side, under the dash. The connector has two wires; one is brown with a black tracer, and the other wire is red.
See Figures 1 and 2
The white mark on the crank pulley is Top Dead Center (TDC).
2.2L/2.3L Odyssey 2.2L models: 13-17Ā° at 650-750 rpm
111 views
Usually answered in minutes!
×