Replace front right wheel bearing - 1995 Oldsmobile Aurora

Fix It Right! - Front Hub Bearing Replacement - YouTube

? 14:26
https://www.youtube.com/watch?v=l0LCkycUcqM
Sep 7, 2011 - Uploaded by OneSourceAutomotive
Front Hub Bearing Replacement (S1E3) Demonstrated on a 2004Kia Sedona FWD. ... on a front-wheel ...

Kia Sportage wheel bearing replacement - YouTube

? 4:10
https://www.youtube.com/watch?v=wa6NREeozbE
Apr 3, 2014 - Uploaded by Jo Daddy's Garage
I did a quick replacement of a bad rear wheel bearing/hub on aKia ... How to install front struts on a Kia ...

sometimes knucke bearings have different sizes, like one side has 4.5, then the other side is 4.6. just make sure that the components are alligned well and if in case a rubber hammer is available, do use it, just apply more grease on the bearing hub, then try to use the rubber hammer to punch the bearing back. please refer to the picture below for the assembly

The other guys have never taken the wheel bearings out of a 2007 Tacoma! Remove the tire (duh)
Remove the 12mm bolt holding the brake line securing bracket
Un-clip the air sensor hose clip
Remove the two 17mm bolts holding the brake assembly on the back side
Remove the rotor from the wheel "spindle"- slides right off.
Unscrew the four metric bolts (maybe 17mm) holding the wheel housing to its mount (they cannot be removed from the assembly yet, see below).
That's right there is no normal wheel spindle with a big nut on the end of a threaded shaft in the middle!
The wheel mounting plate (with the 6 studs) is pressed into the bearing housing.
Get a replacement bearing assembly and take it and your old unit to a machine shop (unless you have a good press).
An easy job, just expensive- $140 for the bearing assembly.

It's most likely the left wheel bearing that's causing the noise, when turning to the right the weight of the car shifts to the left placing more load on the left wheel bearing and takes load off the right bearing.

Unfortunately you do not always get "play" in the bearing and they are unserviceable. Replace the entire unit. Here are the instructions for replacement. They bolt into place making it pretty easy to do. Soak the CV shaft which pertrudes from the hub where the nut goes with a good rust penetrant to ease in removal.

Removal & Installation

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove or disconnect the following:
   
   Front wheel Wheel Speed Sensor (WSS) electrical connector Brake caliper and bracket Rotor Driveshaft nut
   
3. Install a front hub removal tool to the wheel bearing/hub assembly with three wheel nuts. Use the tool to push the driveshaft out of the wheel bearing/hub.
4. Remove the wheel bearing/hub assembly and discard the bolts.

To install:

1. Install or connect the following:
   
   Wheel bearing/hub assembly using new bolts and torque them to 96 ft. lbs. (130 Nm) New drive shaft nut and torque it to 118 ft. lbs. (160 Nm) Brake rotor Front caliper with the bracket WSS electrical connector Front wheel

are your front right brake pads worn more than your front left? if so probable cause is the rotor. if not, most likely wheel bearing

Hi if you are refering to the hub bearing it can not be lubed it is a sealed bearing it will have to be replaced

front right wheel bearing will cost you 80$ might want to check the left side bearing too.

Jack up the wheel that may have the bad wheel bearing and position your left or right hand at the top of the wheel and the other hand at the bottom of the wheel and rock from top to bottom if there is over 1 cm of play your wheel bearing needs to be replaced and if there is excesive play from left to right your rack ends need to be gresed if the have a grease nipple or replaced hope i was some help

You say the rear wheel axles and bearings have been replaced, you mention nothing of the front wheels, you have the symptoms of a front wheel bearing being worn out, remove them and check for pitting in the bearing rollers or the bearing races, I am sure you will find a problem. Hope this helps solve your issue with the bearing noise.