Hard sifting transmission code 17118 gear4 incorrect ratio

Yes, this could be the shift solenoid. Was the transmission filter changed at the same time as the fluid? Dirt in the system can affect some of the transmission sensors tripping Trouble codes. I cannot be sure what the P1732 code is as some codes can be very vehicle specific but it appears to refer to the transmission or on of it's sensors.

P0733 - Gear 3 Incorrect Ratio.
P0734 - Gear 4 Incorrect Ratio.

Codes P0733 and P0736 on a 2002 Jeep Liberty refer to transmission-related issues. Here's what each code indicates: P0733 - Gear 3 Incorrect Ratio: This code indicates that the transmission is not shifting into the third gear correctly. It suggests a problem with the gear ratio between the input and output shafts of the transmission when the third gear is engaged. This could be caused by issues such as a faulty transmission solenoid, a worn or damaged gear, low transmission fluid level, or internal transmission problems. P0736 - Reverse Incorrect Ratio: This code indicates that the transmission is not shifting into the reverse gear correctly. It suggests a problem with the gear ratio between the input and output shafts of the transmission when the reverse gear is engaged. Possible causes could include a faulty transmission solenoid, a damaged or worn reverse gear, low transmission fluid level, or internal transmission issues.

P0734 OBD II Trouble Code Gear 4 Incorrect Ratio YourMechanic Advice

P0735 FORD - Automatic Transmission Incorrect Fifth Gear Ratio Incorrect Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit
P0732 FORD - Automatic Transmission Incorrect Second Gear Ratio Incorrect All - causes would be the same as above with ALSO Probable bad valve body - and or pressure solenoids. Probable bad clutch band. If the fluid is ok and if you have tried changing the fluid and filter to no aval. Is it time to think about a transmission repair at a local transmission shop. Sorry.

change the speed sensors that are throwing the code and then reset codes

2000 land rover discovery II, i have po734, po171, po174 and p1172,po1175, what can I do?

P0732 FORD - Incorrect Second Gear Ratio
Transmission in second gear and the ECM detected an incorrect gear ration. This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows:

Torque converter slip ratio = A x C/B

A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes

If the actual gear position is higher than the position (2nd) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Incorrect transmission shifting

Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Tech notes
Start by inspecting the transmission fluid level and condition, and change fluid if necessary.


Hope helps.

P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

P0700 Transm.Contr.System Malfunction 17084
P0702 Transm.Contr.System Electrical 17086
P0703 Torque Converter/Brake Switch B Circ Malfunction 17087
P0705 Transm.Range Sensor Circ.(PRNDL Inp.) Malfunction 17089
P0706 Transm.Range Sensor Circ Range/Performance 17090
P0707 Transm.Range Sensor Circ Low Input 17091
P0708 Transm.Range Sensor Circ High Input 17092
P0710 Transm.Fluid Temp.Sensor Circ. Malfunction 17094
P0711 Transm.Fluid Temp.Sensor Circ. Range/Performance 17095
P0712 Transm.Fluid Temp.Sensor Circ. Low Input 17096
P0713 Transm.Fluid Temp.Sensor Circ. High Input 17097
P0715 Input Turbine/Speed Sensor Circ. Malfunction 17099
P0716 Input Turbine/Speed Sensor Circ. Range/Performance 17100
P0717 Input Turbine/Speed Sensor Circ. No Signal 17101
P0721 Output Speed Sensor Circ Range/Performance 17105
P0722 Output Speed Sensor Circ No Signal 17106
P0725 Engine Speed Inp.Circ. Malfunction 17109
P0726 Engine Speed Inp.Circ. Range/Performance 17110
P0727 Engine Speed Inp.Circ. No Signal 17111
P0730 Gear Incorrect Ratio 17114
P0731 Gear 1 Incorrect Ratio 17115
P0732 Gear 2 Incorrect Ratio 17116
P0733 Gear 3 Incorrect Ratio 17117
P0734 Gear 4 Incorrect Ratio 17118
P0735 Gear 5 Incorrect Ratio 17119
P0740 Torque Converter Clutch Circ Malfunction 17124
P0741 Torque Converter Clutch Circ Performance or Stuck Off 17125
P0748 Pressure Contr.Solenoid Electrical 17132
P0750 Shift Solenoid A malfunction 17134
P0751 Shift Solenoid A Performance or Stuck Off 17135
P0752 Shift Solenoid A Stuck On 17136
P0753 Shift Solenoid A Electrical 17137
P0756 Shift Solenoid B Performance or Stuck Off 17140
P0757 Shift Solenoid B Stuck On 17141
P0758 Shift Solenoid B Electrical 17142
P0761 Shift Solenoid C Performance or Stuck Off 17145
P0762 Shift Solenoid C Stuck On 17146
P0763 Shift Solenoid C Electrical 17147
P0768 Shift Solenoid D Electrical 17152
P0773 Shift Solenoid E Electrical 17157
P0790 Normal/Performance Switch Circ Malfunction 17174

I can tell you what the codes are but I afraid I don't have an answer as to how to fix it.
700 - Transmission Control System Malfuntion
715 - Input/Turbine Speed Sensor Circuit Malfunction
731 - Gear I Incorrect ratio
733 - Gear 3 Incorrect ratio
734 - Gear 4 Incorrect ratio