At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Had driver door replaced , Non locking Switch won't work, Mirror switch wont work, Inside lights won't come on when door is open, radio wont work, clock won't work. The machine said nothing they did would affect these things. But I think different. Any ideas!
Thank you checked connection, Noticed they have cut the wives that go to the Keyless inter. and didn't reconnect them. Could this be cursing all the problems.Thank you checked connection, Noticed they have cut the wives that go to the Keyless inter. and didn't reconnect them. Could this be cursing all the problems.
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The door switch is located inside of the door latch. You probably have a bad switch and need to have the latch changed. Since the drivers door gets the most use, that is a good place to start.
Yes they run a wire loom that has wires that are not used in some models. One thing you need to check is the wire loom because it flexes every time the door opens and closes and wires can break .Also you may want to go to autozone website and make a free account, you can put in the year make and model and look for the free repair guides for wire diagrams.
Check the electrical connections for you control switches...there should be at least two of them. Disconnect them and see if there are any recessed pins or dirt. Do this several times as there may be some oxidation on the connectors and doing this will help clean them off. The radio and door light works of the small limit switch on your door frame. Everything else works through the operators window/door lock control panel.
If only the door ajar light and interior light is not working it is probably the door ajar switch located on the door latch inside the door. sometimes a little WD40 sprayed towards lower side of the latch will work, frees the piston in the switch. if not the switch must be replaced. If also the outside mirror control does not work, the door lock switch also does not work, it is a bad ground to those three systems, the Electric windows have a separate ground wire and still work. You must feed a new black wire from a good ground on the body thru the door accordion tube and connect it to the larger black wire on the plug that goes to the door lock switch. The door lock, the mirror control, the door ajar light, and the interior light problem will be gone.
FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.
Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim
panel. Disengage wire connector from switch panel, if equipped Power
Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage
clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.
Hope helped with this; remember rated this help. Good luck.
Remove the door handle bezel.Remove the power window/door lock switch bezel.Remove the rearview mirror fastener trim cover.Remove the 4 door trim panel retaining screws.One that was behind the mirror trim cover,behind the switch panel,behind the door handle bezel,and one at the bottom corner.Lift the door trim panel up from the door to disengage the trim panel clips.Remove the front radio speaker. Disconnect the power mirror wiring connector.Remove the 3 bolts to the mirror.
I had this problem on my 2003 explorer and took WD40 and gave the lock mechanism a good dose where it meets the clasp on the door jam. Then open and close the doors a couple of times to get them working. They get gummed up and sometimes have a tendency to stick.
There is a child safety switch on the rear latch assembly that prevents opening from the inside handle. This switch may be on. Check your owners manual for more info.
Thank you checked connection, Noticed they have cut the wives that go to the Keyless inter. and didn't reconnect them. Could this be cursing all the problems.
×