Help in removing headlight assembly - 1995 Volvo 940

On some cases there are few hidden clips holding the assembly from under hood,that has to be released to remove headlight .

There are few troubleshooting help links showing how to replace car headlights,i suggest you to refer the links to solve these issue.

--------
Click the link below:------
How to Replace a Headlight http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight.html

------------
How to Replace a Headlight Bulb

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-bulb.html

-----------
How to Replace a Headlight Switch http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-headlight-switch.html

----------
How to Replace a Headlight Assembly

http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-assembly.html

How to Replace a Park Light Assembly http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-park-light-assembly.html

-----------
Low beam headlights Modification? http://schematicsdiagram.blogspot.in/2012/04/low-beam-headlights-modification.html

----------
Headlight Assembly Removal On Honda Accord http://technoanswers.blogspot.in/2012/06/headlight-assembly-removal-on-honda.html --------------- Honda Headlight Assembly Removal
http://schematicsdiagram.blogspot.in/2012/06/honda-headlight-assembly-removal.html-----------
How to Replace a Headlight Door http://schematicsdiagram.blogspot.com/2011/08/how-to-replace-headlight-door.html

---------
All headlights not working? http://repairhelpcenter.blogspot.com/2012/01/all-headlights-not-working.html

----------
How to replace HID headlight bulbs for lexus 400h? http://schematicsdiagram.blogspot.com/2012/01/how-to-replace-hid-headlight-bulbs-for.html

----------
• Working of Headlight switch?
------------
• Both headlight bulbs blow together?
------------
• Car headlight bulbs don't last long?


----------------
These will help.
Thanks.

1. INSTALLATION GUIDE:
2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
3. Parts Identification:
4. Projector Headlight
5. Halo & L.E.D.
6. Bottom of the Headlight:
7. Ballast Bracket, Halo Wires(red/black)
8. Turn Signal Adaptor
9. TOOLS REQUIRE
10. 10mm - 8mm socket
11. Philip Screwdriver
12. Crimper/Pliers
13. For more information about how to install your vehicle, come visit our youtube page on
14. http://www.youtube.com/spyderauto
15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
21. STEP:
22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
24. Factory Xenon Headlight
25. Spyder Projector Headlight using Factory Xenon Lights
26. STEP:
29. PLS VOTE ME

BMW e46 HID Headlight Replace

HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly

Step 1:
Be sure the ignition key is not in the ignition, and the headlight switch is in the "Off" position.



Step 2:
Locate and remove the two headlight assembly screws on the top rail of the headlight assembly. Use the nut driver to remove them.


Step 3:
Place a rag between the headlight assembly and the bumper to protect the paint.


Step 4:
Wrangle the assembly outward. There is a guide pin behind the assembly on the fender side that holds it in place. This needs to be popped out of its socket in order to remove the headlight assembly. Pull slightly outward from the side, then forward and away from the car.


Step 5:
Locate the correct bulb socket (high-beam/low-beam). Disconnect the wire connector using the flathead screwdriver.


Step 6:
Turn the socket 1/4-turn counterclockwise to remove the socket from the headlight assembly. Remove the old bulb.


Step 7:
Insert the new bulb into the headlight assembly, and turn clockwise to lock into place. Be careful not to touch the glass bulb of the new socket. This could degrade headlight performance.


Step 8:
Reconnect the wire connector to the bulb. Test the light before replacing the headlight assembly, then turn off the lights again.


Step 9:
Reinsert the headlight assembly, making sure to align the guide pin into the socket. Replace the screws and tighten.

Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:

1. Open the hood.
2. Remove the front air deflector.
3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
4. Lift up the headlight retainers to release the housing.
5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
   
6. Disconnect the wiring harness from the headlight assembly.
7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
8. Remove the bulb(s)/socket(s) from the headlight assembly.

To Install:

1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
2. Connect the wiring harness to the headlight assembly.
3. Position the headlight assembly to the mounting panel.
4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
6. Install the front air deflector.
7. Close the hood.

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Disconnect the negative (-) battery terminal.
   
3. Loosen the mounting bolts and nut of headlight assembly (A).
   

   Loosen the mounting bolts and nut of headlight assembly (A)-Santa Fe
   Click to Enlarge

   Loosen the mounting bolts and nut of headlight assembly-Veracruz
   Click to Enlarge

4. Take care that retaining clip (A) is not to be damaged-Santa Fe.
   

   Take care that retaining clip (A) is not to be damaged-Santa Fe
   

5. Disconnect the headlight electrical connectors.
   
6. Remove the headlight assembly.
   
7. Remove the headlight bulb:
   
   • Remove the headlight bulb(s) with a counterclockwise turn-Santa Fe.
     
   • Remove the headlight bulb after removing the bulb caps (A)-Veracruz.
     

     Remove the head lamp bulb(s) with a counterclockwise turn-Santa Fe
     

     Remove the headlight bulb after removing the bulb caps (A)-Veracruz
     

To install:

1. Install the headlight bulbs.
   
2. Install the headlight bulb caps-Veracruz.
   
3. Connect the headlight electrical connector.
   
4. Install the headlight assembly.
   
5. Connect the negative (-) battery termina

once bolts out lift up on the headlight unit hope this helps plz vote comment reply if you need more help

LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . .
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . .
Fig. 6: . . . then pull the retaining ring off of the headlight assembly
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight

1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
3. Install the headlight in the reverse order of removal.

Grand Cherokee and Grand Wagoneer Models

1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
   
3. Install a new bulb and position the bulb assembly in the lamp housing.
4. Rotate the lock ring 1?8 turn clockwise to secure.

----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

You have to remove the headlight assembly to remove the turn light assemble. There are two mounting bolts that hold the headlight assembly to the frame that needs to be removed and one mounting bolt that holds the turn signal light assembly on the headlight assembly that needs to be removed. Once all three bolts (black plastic in colour with a wing nut) have been removed the headlight and turn signal assembly can just be removed. Take note that the assembly has a guild slot to be guild in place back when re installing the head light and turn signal assembly. Good luck and hope this helps. Keep me posted and I'll try to explain in a different way if i was un clear, Harder to explain then doing the job it self. 

1) Lift up on the headlight retainer to release the headlight assembly. 2) Release the headlight ball studs from the grommets by pulling the headlight assembly from the lower center corner. 3)Remove the headlight assembly from the upper fascia support. 4) Disconnect the harness connector from the headlight assembly. 5) Remove the headlight assembly from the vehicle. 6) Remove the access cover from the rear of the headlight assembly. 7) Remove the headlight bulb socket from the headlight assembly by rotating counterclockwise . 8) Remove the headlight bulb from the socket. Reverse these steps to install and make sure when your done to adjust the headlight.

it is behind the passenger side headlight assembly. you will have to remove the headlight assembly to replace it. I hope this helps.