RADIO JUST SAYS AUDIO OFF WILL NOT TURN ON - 2007 Lexus GS 350 AWD Sedan

The 2015 Nissan Altima does not have a mute button for the Audio system. To unmute the Audio system You will have to turn the volume knob clockwise. If this does not fix the problems with the Audio in the vehicle You can try and attempt a full reset of the radio in Your car. To do this You will turn the ignition key to the "on" position and turn Your radio on, wait ten seconds and then turn Your radio off. Depress the radio power button again and wait for reset. Alternatively, enter Your dealer provided radio code to reset. You can also check to see if You had a call and if You did not press the "call hang up" button on the steering wheel while not on a call it could mute the radio so press it again to un mute it.

Question edited for clarity.
Question moved to model category.

It appears to be a software error that only the dealership or an auto electrician can fix!

https://www.google.com/search?q=2002+trailblazer+radio+cal+error

..

Which of these does your truck have ?
The Entertainment System on this vehicle is configured with a radio, antenna, and speakers.
The following list shows the radios available for this vehicle:
• Radio (UM7) - AM/FM with Cassette
• Radio (UB0) - AM/FM with CD
• Radio (UB1) - AM/FM, Cassette and CD
• Radio (UC6) - AM/FM, Integral Multi Disc CD Changer
Audio Amplifier
The audio amplifier is standard on some vehicle lines but is optional on most. The radio supplies low level audio signals to the audio amplifier in order to boost the signal sent to the speakers. The class 2 signal circuit allows the radio to recognize that an amplifier is present. Once the radio detects an audio amplifier, it will output low level audio signals. The audio amplifier is turned on when it receives a message via the class 2 serial data circuit indicating that the radio is on.
Digital Radio Receiver
The radio communicates with the digital radio receiver via the class 2 communications circuit. The digital radio receiver sends low level audio signals to the audio amplifier.
Steering Wheel Controls
Some audio functions are available using the steering wheel controls. The steering wheel controls consist of multiple momentary contact switches that connect a series of resistors. When a steering wheel control button is pressed, a specific resistance value is noted by the body control module (BCM). This results in a generated voltage, unique to the particular button. The BCM alerts the radio that the button has been pressed, and the radio responds, just as if the corresponding radio front panel button had been pressed.
Amplifier
The amplifier in early build vehicles is a class 2 device that communicates with the scan tool on the Class 2 bus. The Class 2 amplifier will set a U100 in the radio if there is a communication problem. The late build vehicles have a NON-Class 2 amplifier that does not communicate over the Class 2 bus and therefore the NON-Class 2 amplifier will not set codes. Both amplifiers have similar operating characteristics, therefore, there are not separate diagnostics for the NON-Class 2 amplifier.
Circuit Description
When the radio is powered up, the radio supplies low level audio signals to the speakers. If the vehicle is equipped with an audio amplifier, the amplifier will boost the signal sent to the speakers. The radio tests the speaker output circuits for a short to voltage or ground.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
• DTC B1025 Audio Output 1 (Left Front) Circuit
• DTC B1035 Audio Output 2 (Right Front) Circuit
• DTC B1045 Audio Output 3 (Left Rear) Circuit
• DTC B1055 Audio Output 4 (Right Rear) Circuit
Reduced Volume - One or More Speakers
Step
Action
Yes
No

Schematic Reference: Radio/Audio System Schematics

1
Did you perform the Diagnostic System Check - Vehicle?
Go to Step 2
Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
Turn ON the ignition, with the engine OFF.
Turn ON the radio.
Adjust the radio balance and fade controls to each speaker.
Do all of the speakers operate properly?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3

3
Turn the ignition ON, with the engine OFF.
Adjust the volume level.
Test the appropriate speaker output circuits of the radio for A/C voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did the A/C voltage fluctuate with the audio output?
Go to Step 4
Go to Step 8

4
Turn OFF the ignition
Disconnect the radio.
Test the appropriate speaker output circuits of the radio for high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 5

5
Inspect for poor connections at the harness connector of the radio. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 6

6
Inspect for poor connections at the harness connector of the appropriate speaker. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 9
Go to Step 7

7
Replace the speaker. Refer to Speaker Replacement Reference .
Did you complete the replacement?
Go to Step 9
--

8
Replace the radio. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 9
--

9
Operate the system in order to verify the repair.
Did you correct the condition?

Turn radio on or turn ignition on - radio will show a number of lines on screen. enter code with numbers pad one code number at a time until next flashing bar opens and wait 10-20 seconds. If failed start procedure from scratch.

You need to enter the ford audio units security code into the audio unit. Because the battery was out for a long time, the audio unit has forgotten its security code. The code is in the manual that came with the car.

Here you go. Be careful this can disable the truck in some models due to the radio system be tied into the factory anti theft system..

2009 Chevrolet Tahoe Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Red/White
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. The accessory turn-on is controlled by the lan serial network. Run a wire to the fuse box or ignition switch harness.
Car Radio Ground Wire: Black
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: The radio harness does not provide a dimmer wire. The dimmer wire is controlled by the lan serial network.
Car Stereo Antenna Trigger Wire: The radio harness does not provide a antenna trigger wire. The antenna trigger wire is controlled by the lan serial network.
Car Stereo Amp Trigger Wire: The radio harness does not provide a amp turn on wire. The amplifier turn on is controlled by the lan serial network.
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

If an audio unit with theft protection is disconnected from electrical power, you must enter a unique code number into the unit or it will not work. This code and the audio unit’s serial number are listed on the anti-theft ID card that comes with the vehicle (some people say that they find it on a sticker in the glove compartment, but I wouldn't count on that). If this card is lost, you must obtain the audio unit serial number in order to get the radio code. Some newer vehicles allow you to retrieve the audio unit serial number electronically from the radio. Refer to your owner’s manual for the specific procedure (the following usually will work: Turn the radio off. Push the preset 1, preset 6, and power buttons at the same time, then quickly release. The code will come up to two sets of numbers)
Once you have the audio unit serial number, you can call Auto Customer Service at (800) 999-1009 or have the dealer look up the radio code.

The bluetooth and radio are located in the radio itself. I would suggest having the radio replaced at you local toyota dealership

I have the SAME EXACT problem. I thought it was the radio - bought another - went to change the units - heard an electrical arc - now the car cranks but doesn't start and the new radio doesn't work either!!! (not that it matters anyway)
Is there an electrical problem with '96 Lincoln's. Where should I start to diagnose the non-starting issue?