At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Where is the oil filter located in a 2003 Chrysler 300mWhere is the oil filter located in a 2003 Chrysler 300m
AnonymousMar 17, 2014
Trying to find an OWNERS and a SERVICE Manual specific to the 2004 Chrysler 300M SPECIAL - not the 300M, but the 300M SPECIALTrying to find an OWNERS and a SERVICE Manual specific to the 2004 Chrysler 300M SPECIAL - not the 300M, but the 300M SPECIAL
AnonymousMar 17, 2014
Trying to replace the oil pressure sensor and need a diagram of the engine that shows where it is located.Trying to replace the oil pressure sensor and need a diagram of the engine that shows where it is located.
AnonymousMar 17, 2014
just need information on how to remove and replace waterpump on chrysler 300mjust need information on how to remove and replace waterpump on chrysler 300m
AnonymousMar 17, 2014
need to replace the water pump on a 2004 chrysler 300mneed to replace the water pump on a 2004 chrysler 300m
AnonymousMar 24, 2014
where is the fuse located, how is it labeledwhere is the fuse located, how is it labeled
AnonymousMar 28, 2014
replace alternator belt on Chrysler 300M 3.5 enginereplace alternator belt on Chrysler 300M 3.5 engine
You can't post conmments that contain an email address.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
whar steps do I take after draing the coolant from the radiator. I have a 1999 chysler 300m. Should the engine be running while replacing the coolant. This car does not have a radiator cap to remove. Do I just add the coolant in the resivor while the engine is running?
Hi,
On2.7L models, the IAT sensor is located on the left side (driver) of the Intake Manifold plenum, if you are standing in front of the car, it is the sensor right before the two vacumm hoses plugged into the Intake Manifold.
On 3.2L/3.5L models, the IAT sensor is incorporated whthin the Map sensor which is also located on the left side (driver) of the upper Intake Manifold plenum. Right by the coolant reservoir tank.
The belts need to be removed and they take a special wrench. If you have to ask how chances are this is best left to the experts. The plastic sensors etc can cost you way more than any potential savings. There are several engine combination's of motors on this car and you don't say which it is you have. Best to leave this one to the experts.
If you insist - then remove the negative battery cable - remove the cover on top of the engine remove the belt [s] remove the hoses to the power steering pump remove the bolts and the power steering pump assembly - reverse this procedure and then 'bleed the lines' to remove any air.
Again I strongly suggest you leave this job to the experts.
Hello, Had the same problem but i did just the opposite I put a 2002 engine in a 2000. I found out that the cam sensor spocket (for the timing belt) Has the holes for the cam sensor in a different spots causing all kinds of problems also they did the same with the flex plate so I hope you took the one off the 2002 and used it or you will have to pull it back out and change it. Good luck
The Coolant temp Sensor is located right under the top radiator hose (on the engine side), with a little black connector!, You might have to remove th etop hose to get to it with a deep socket and extension!.
Also Dont Forget to blled the coolant system by the bleeder valve uptop right near/above the coolant sensor!.(10MM Mini socket w/ extension IIRC!)
You need to bleed the Cooling system(While engine is on...) through the bleeder valve on top of the engine (w/ heater selected ON,and on High Speed ofcourse!).
Where is the oil filter located in a 2003 Chrysler 300m
Trying to find an OWNERS and a SERVICE Manual specific to the 2004 Chrysler 300M SPECIAL - not the 300M, but the 300M SPECIAL
Trying to replace the oil pressure sensor and need a diagram of the engine that shows where it is located.
just need information on how to remove and replace waterpump on chrysler 300m
need to replace the water pump on a 2004 chrysler 300m
where is the fuse located, how is it labeled
replace alternator belt on Chrysler 300M 3.5 engine
×