Engine stutter fuel p1336 - 2009 Mazda MAZDA6

Did you reset the code after the replacement?

Camshaft / Crankshaft Sensor is the reason for the code. They come in different qualities. OEM is best, made in Mexico is the worst!

PREVIEW
8:17 2002 Ford F150 - Codes P0340 and P1336: Cam Position ...
YouTube · Bent Oaks Garage Nov 30, 2021 PREVIEW
6:37 How to change Camshaft Position Sensor (CMP) - 2002 Ford ...
YouTube · Innova Feb 26, 2016 10 key moments in this video













PREVIEW
13:18 Ford 4.2 L Camshaft Position Synchronizer Replacement ...
YouTube · JamesonDIY Sept 8, 2019 10 key moments in this video













View all

P1336 2002 FORD F150 - Engine-Codes.com

https://www.engine-codes.com > p1336_2002_ford_f150
'P1336 2002 FORD F150 code possible causes · Faulty Crankshaft Position Sensor · Faulty Camshaft Position Sensor · Crankshaft Position Sensor harness is open or ...

P1336 Ford P1336 Ford - Crankshaft Position Or Camshaft Position Sensor Input Signal Error Share
0 ' Add Comment Possible causes
- Faulty Crankshaft Position Sensor
- Faulty Camshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
What does this mean? When is the code detected?
The Engine Control Module (ECM) has detected a synchronization or signal error from the cam or crank sensors
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
- Engine difficult to start
P1336 Ford Description
The input signal to the powertrain control module (PCM) from the crankshaft position (CKP) sensor or the camshaft position (CMP) sensor is erratic.

Read more: http://www.engine-codes.com/p1336_ford.html#ixzz3qT9Hiztc

1. Clogged fuel filter; or
2. Bad fuel pressure regulator; or
3. Clogged fuel pickup strainer in gas tank ("fuel sock"); or
4. Water or other contaminant in fuel (replace all fuel with new).

http://www.therangerstation.com/tech_library/camshaft_position_sensor.shtml

Here's what I've found about this P1336 code:
P1336 Crankshaft sensor is out of sync with camshaft sensor test
If you get this code, the first thing to check is your distributor especially if you have an imported vehicle. Look for signs of oil in the distributor which can contaminate the signals being monitored by the ECM (engine computer). Check also the wiring leading to the distributor and see if the wires are properly insulated away from hot exhaust which could burn the wires. Check also on the crank sensor location whether it is located in the front of the engine or at the flywheel at the rear of the engine. The same can be done for the cam sensor.
On engines with distributor, the cam sensor is usually located in the distributor and it will give you a lot of grief if not properly align and synchronize with the crank sensor. On some applications (like Ford), an alignment tool is required which is can be bought from your local parts store (cost about $31). If you install the distributor without proper timing, it will still run but the mileage will suffer and the above code showing up.
Your local trusted mechanic or Ford Dealer should be able to resolve this for you (if you can't) without too much trouble.

The crank position sensor is not sending a signal to the computer.
Could be the sensor, the wiring, or the sensor plate.

P1336--CKP or CMP Input Signal to PCM Concerns

Check Crank & Cam Sensors for their installation & wire
connector

After that a repair shop will be needed

The code is your symptoms to a Tee

Trouble Code: P1336

CKP Sensor System Variation Not Learned
Possible Causes:


Set the parking brake and block the drive wheels for safety. Verify the hood is closed. Read the trouble codes. If a code is set, refer to that code. Start the engine. Allow engine temperature to reach at least 158?F (70?C). Then key off. Select Crankshaft Position Variation Learn procedure on Scan Tool & start the vehicle. Apply the brake pedal firmly and verify the selector is in Park. Increase accelerator pedal position until fuel cutoff is reached at the test rpm (e.g., 5150). Quickly release the accelerator pedal after fuel cutoff is reached. The CKP system variation compensating values are learned when the engine speed (rpm) decreases back to idle speed and the procedure terminates. Read the trouble codes and recheck for DTC P1336. If DTC P1336 runs and passes, the CKP system variation "learn" procedure is complete. If not, look for other codes. If no codes are set, repeat the test procedure.

If this is a P1336 read on.
P1336 - Crank / Cam Sensor Range / Performance
Possible causes

Damaged PCM.

Damaged CKP sensor. (crankshaft position sensor)

Damaged CMP sensor. (camshaft position sensor)

Base engine concerns.

Wiring Harness Concerns.

CHECK FUEL PRESSURE. COULD BE FUEL PUMP.CHANGE FUEL FILTER IF IT HAS NOT BEEN CHANGE IN A WHILE.