Trouble code c0455 c0292 - 2005 Chevrolet Tahoe

DTC C0292: VSES Combination Sensor Circuits .

This has nothing to do with the PCM

Circuit/System Description
The electronic brake control module (EBCM) supplies a reference voltage of 12 volts to the yaw rate sensor lateral accelerometer and the steering wheel position sensor. The sensor supply voltage is monitored via an internal feedback circuit to the EBCM microprocessor.

Conditions for Running the DTC
• The ignition is ON.
• Ignition voltage is greater than 9.5 volts.
Conditions for Setting the DTC
The yaw/lateral sensor is setting an internal electronic failure.

Your best bet ,have a qualified repair shop check it out .

You should have started by getting the trouble codes read. Any time you have a warning message or light, there's a trouble code stored. In the meantime see this post on this common GM issue

https://ricksfreeautorepairadvice.com/service-stability-c0710-c0455/

Go under and make sure you connected all the connections on the rack and make sure no pins are pushed out of the connectors and they are fully latched, replace any with broken connector shell lock tabs.

C0292
Lost Communications with Engine Control System
EBCM
DTC C0290 or C0292 in Antilock Brake System
Your best bet ! Take it to a quaified repair shop . Do you know what Class 2 data bus is ?

Class 2 Serial Data Line
The class 2 serial data line on this vehicle is a star configuration. The following modules communicate on the class 2 serial data line:
• Audio Amplifier, w/UQ7 and Y91
• Body Control Module (BCM)
• CD Changer (CDX), w/U1S and Y91
• Digital Radio Receiver (DRR), w/U2K or U2L
• Driver Door Module (DDM)
• Driver Seat Module (DSM), w/AN3
• Electronic Brake Control Module (EBCM)
• Electronic Suspension Control (ESC) Module, w/Z55
• Front Passenger Door Module (FPDM)
• Generator Battery Control Module (GBCM)
• HVAC Control Module
• HVAC Control Module - Rear Auxiliary
• Instrument Panel Cluster (IPC)
• Powertrain Control Module (PCM)
• Radio
• Rear Seat Audio (RSA) Controller, w/UK8
• Rear Seat Entertainment (RSE) Assembly, w/U42
• Rear Wheel Steering Control Module (RWSCM)
• Inflatable Restraint Sensing and Diagnostic Module (SDM)
• Transfer Case Shift Control Module (TCSCM), w/NP1/NP8
• Vehicle Communication Interface Module (OnStar), w/UE1
• Vehicle Theft Deterrent (VTD) Module, w/VD1
The class 2 serial data line allows a scan tool to communicate with these modules for testing purposes, checking for DTCs, and to activate/enable/disable functions. These class 2 serial data circuits are bused together via three splice packs and DLC:

First you need to have EBCM - electronic brake control module check for DTC'S - diagnostic trouble code's . If the light is on there is a code stored . I think most part stores can do this and for free . After you find out what code is stored , looking up that code in service repair information for diagnostic trouble shooting chart would be next step . There are a few codes too.
DTC C0035 or C0040
DTC C0045 or C0050
DTC C0110
DTC C0131
DTC C0161
DTC C0186
DTC C0196
DTC C0201
DTC C0240
DTC C0241 or P0856
DTC C0244 or P1689
DTC C0245
DTC C0283
DTC C0287
DTC C0290 or C0292
DTC C0455
DTC C0550
DTC C0558

Find the code do the diagnostic's , fix the problem , wiring issue's , a sensor , bad module ,what ever it is . The light will go out then . Here is a sample of code discription .
• DTC C0035 Left Front Wheel Speed Sensor Circuit
• DTC C0040 Right Front Wheel Speed Sensor Circuit

C0040 - Right Front Wheel Speed Circuit Malfunction
C0550 - ECU Malfunction - internal write / checksum malfunction
C0455 - Either:

• A bent terminal or poor connection at the SWPS may be one possible cause; or
• The vehicle stability enhancement system (VSES) electronic brake control module (EBCM) calibration may be the other possible cause.

C0296 - Transfer Case Delivered Torque for Stability Control System Circuit
http://www.obd-codes.com/trouble_codes/obd-ii-c-chassis-codes.php

Don't know where you came up with this one D0131 , No such code . Now if you mean a P0131 it's for a O2 sensor
DTC P0131 HO2S Circuit Low Voltage Sensor 1
C0455
Front Steering Position Sensor Circuit
EBCM

The electronic brake control module (EBCM) receives multiple direct inputs from the steering wheel position sensor. These circuits include, two digital square wave input signals A and B. Phase A or B should toggle high and low every 2 degrees of steering wheel rotation. . The EBCM also receives one analog steering wheel position input on the steering wheel position sensor signal 1 circuit, and is compared to the digital circuits for fault detection. The analog portion of the steering wheel position sensor is supplied a 5-volt reference and low side return circuits from the EBCM. Ignition voltage and ground circuits are supplied directly to the digital portion of the steering wheel position sensor.

This diagnostic procedure supports the following DTC:
DTC C0455 Front Steering Position Sensor Circuit