Starter motor diagram

the good thing about starter motors is they are all constructed the same so any wiring diagram of a starter / overhaul manual for starters will show how it is made and the wiring diagram of the fields , armature and solenoid
if you go google and type in ---workshop manual for evinrude 60 hp 1994 outboard engine -- you may find a pdf version to download

Its located in the under hood engine compartment fuse box.

There will be three same relays.One for fuel pump and other for horn and bit bigger one for starter controlling.

For more help regarding starter

CAR STARTER REMOVAL? TESTING

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----

How to test starter solenoid?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html

--------------------

How to test cars starter?

http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html

-----------

How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------

How to replace Starter on Infiniti Q45?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------

2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----

Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

CAR STARTER REMOVAL? TESTING

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============

For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----

These help links will help.

Click the link below:-----

How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html ----------- How to replace starter in car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html

-----------
How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html

----------
2006 GM Montana: How to replace Starter Solenoid?

http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html

-----
Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?

http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html

----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------

Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?

------------

These details will help.

Thanks.

One Wire From Starter Motor Goes To Solenoid And Other Goes To BATTERY. Starter GETS 12 VOLT SUPPLY FROM BATTERY AND WITH THESE VOLTAGE IT TURNS THE MOTOR AND THIS TRIGGERS THE STARTER SOLENOID AND YOUR VEHICLE RUNS.============
For your help there are few relatively help links showing how to remove and install starter with proper instructions:-----
These help links will help.
Click the link below:-----

How to test starter solenoid? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-starter-solenoid.html -------------------- How to test cars starter? http://schematicsdiagram.blogspot.com/2011/06/how-to-test-cars-starter.html----------- How to replace starter in car? http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-starter-in-car.html
-----------How to replace Starter on Infiniti Q45? http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-starter-on-infiniti-q45.html
---------- 2006 GM Montana: How to replace Starter Solenoid? http://repairhelpcenter.blogspot.in/2012/06/2006-gm-montana-how-to-replace-starter.html
-----Saturn SL2: How to replace Starter Motor?

http://howtobyme.blogspot.in/2012/06/saturn-sl2-how-to-replace-starter-motor.html

--------

Saturn SL2 Starter Wiring Diagram?
http://schematicsdiagram.blogspot.in/2012/06/saturn-sl2-starter-wiring-diagram.html
----------

• Oldsmobile starter solenoid replacement procedure?...

--------------------

• How to replace Oldsmobile starter moor?

----------

• Oldsmobile starter motor testing?

-------------
Oldsmobile STARTER MOTOR NOISE DIAGNOSIS?
------------These details will help.Thanks.

Hi there:

1. If necessary for access, remove the splash shield.
   
2. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
   
3. Label and detach the electrical connectors from the starter.

Fig.: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion




Fig.: Exploded view of the starter motor mounting - 1987-97 vehicles

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)

1. Disconnect the negative battery cable.
2. Raise and support the vehicle safely.
3. If necessary for access, remove the splash shield.
4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
5. Label and detach the electrical connectors from the starter.

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion



Fig. 3: Exploded view of the starter motor electrical connections

1. It may allow more room it you remove the right side cooling fan.
2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)



Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation



Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle


Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.



Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles


To install:
Note the location of any shims so they may be replaced in the same positions upon installation.

1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
4. If removed, install the splash shield.
5. Carefully lower the vehicle.
6. Connect the negative battery cable.

Hope helps (remember rated and comment his).

Fig. 4: Exploded view of the starter motor mounting-2.0L engine




Fig. 6: Starter motor wiring terminal connections-2.0L SOHC engine with A/T; 2.4L engine


Hope helps (remember rated this).

REMOVAL & INSTALLATION
(see Figures 2, 3, 4, 5, 6 and 7)

1. Disconnect the negative battery cable.
2. Raise and support the vehicle safely.
3. If necessary for access, remove the splash shield.
4. If equipped, unfasten the flywheel inspection cover bolts and remove the cover.
5. Label and detach the electrical connectors from the starter.
   

Fig. 2: Unfasten the starter motor electrical connections. You may want to tag them first to avoid confusion



Fig. 3: Exploded view of the starter motor electrical connections

1. It may allow more room it you remove the right side cooling fan.
2. Remove the starter-to-engine bolts, then carefully lower the starter from the vehicle.

Fig. 4: The starter is attached to the engine with 2 mounting bolts (see arrows)



Fig. 5: Unfasten the front mounting bolt (1) and remove any necessary shims (2), noting their locations for installation



Fig. 6: Unfasten the long starter mounting bolt, then remove the starter motor from the vehicle

Before installing the starter motor, make sure the electrical terminals are secure by tightening the nuts next to the cap on the solenoid battery terminal and on the "S" terminal. If these terminals are not tight in the solenoid cap, the cap may be damaged during installation of the electrical connections and cause premature starter failure.



Fig. 7: Exploded view of the starter motor mounting - 1987-97 vehicles

To install:


Note the location of any shims so they may be replaced in the same positions upon installation.

1. Place the starter in position, then install the starter-to-engine bolts and tighten to 32 ft. lbs. (43 Nm).
2. Attach the electrical connectors to the starter, as tagged during removal. Tighten as follows:
   
1. Tighten the nut on the solenoid battery terminal to 12 ft. lbs. (16 Nm).
2. On the SD-250 and SD-255 models, tighten the nut on the "S" terminal to 22 inch lbs. (2.5 Nm).
   


3. If removed, install the flywheel inspection cover and secure with the retaining bolts. Tighten the flywheel cover bolts to 62 inch lbs. (7 Nm).
4. If removed, install the splash shield.
5. Carefully lower the vehicle.
6. Connect the negative battery cable.

Hope helps (remember rated and comment this).

Exploded view of the starter-5.2L and 5.9L model shown



Also I suggest check the ZJ-Secc-8B-Battey-Starter-Motor-Generator-Service for other details.

Hope help with this.

Remove or disconnect the following:

• Negative battery cable
  
• Air inlet duct
  
• Top starter bolt
  
• Lower starter bolt
  
• Starter electrical connectors
  
• Starter motor
  

Exploded view of the starter motor—2.4L engine

To install:

1. Install or connect the following:
   
   • Starter motor. Torque the bolts to 66 ft. lbs. (90 Nm) for 2.4L engine or 37 ft. lbs. (50 Nm) for the 2.2L (VIN 4) engine or 30 ft. lbs. (40 Nm) for the 2.2L (VIN F) engine.
     
   • Starter electrical connectors
     
   • Air inlet duct to the throttle body
     
   • Negative battery cable