Question about 1987 Dodge Ram Wagon B250

Open Question

My corolla altis 2002 valve body automatic transmission need to replace the ball bearing in the proper way

Posted by Anonymous on


2 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017



  • 1 Answer

SOURCE: body valve

Everythings ok thanks

Posted on Jan 20, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where do the check balls get placed in the valve body of transmission?

look on spacer plate if you look close you will see where thy go

Apr 16, 2015 | 1996 Dodge Neon

1 Answer

How bad is it to replace epc solenoid on a 4T65-E automatic gm transmission

the side pan will have to be removed and axle shaft plus lower left side of the subframe for clearance and then remove the valve body assy ..there are several ball bearings positioned in strategic locations for pressure control that is not put back in the right position this trans will not shift correctly also when bolting the valve body back special torque sequence must be performed or the trans will still have a harsh shift . I recommend that a qualified transmission shop do the work on this trans or you are throwing away your money ...sorry

Mar 25, 2015 | 2004 Buick Rendezvous

1 Answer

1997 isuzu rodeo transmission valve body ball bearing location

that will take a real isuzu full transmission FSM book.
or from the true maker, see that tag on the tranny?
it answer that. on most cars.
will say like Aisin mfg company model x. or ????????

there are 2 choices.

Mar 23, 2015 | 1997 Isuzu Rodeo

1 Answer

My corolla altis 2002 model makes noise during idling and when trying to accelerate noise comes more louder and it doesnt have power but i changed the timing kit and the valves,it also shows the engi

I'm pretty good with noises, but to answer your question, you're going to have to describe the noise itself. For example, at idle you hear a clicking, chattering, squeaking or rattle. If you can also let us know where the "noise" is coming from (engine, trans, drive axle) that would also be helpful. Try to be as descriptive as possible, so somebody can help you out. Most people have experienced the same issues and can help if given a better description.

Aug 21, 2014 | Cars & Trucks

1 Answer

I have a 06 camary only gerks while drive 20 to 25 miles anything more it fine v6 3.0 automatic trans what's wrong it

It could be dirty or burned transmission fluid or it could be one little check valve ball in your valve body for your automatic transmission. Avalon's use to have similar issue and that was the fix replace valve body with new and improved one. I would definately make sure fluid is good and at proper level before condemning anything though

Aug 05, 2014 | Cars & Trucks

1 Answer

Altis wont start

Did u check to see if you have a god battery and starter

Jun 30, 2014 | 2002 Toyota Corolla

1 Answer


Those are valve body check balls and they must be put back in the proper place for the transmission to function properly. Try not to panic. If you look closely at the passages in the valve body, you will probably notice that some of the them have small indentations beside them. If you find passages with this difference in the same number as the check balls, then install them and then install the valve body by lifting it straight up and carefully aligning it with the transmission housing before making contact with it. Good luck with your effort. I hope this information has been helpful and thank you for trying

Jun 21, 2011 | Dodge Grand Caravan Cars & Trucks

1 Answer

Is tune up needed in toyota altis 2002? gas consumption has gone up to 6 kms. per liter

officially, there are no "tune-ups" anymore
there are just "maintenance" schedules
you did not list miles and or engine but I am assuming you are over 150k and have a 4cyl

therefore the following should have been replaced
spark plugs
fuel filter
air filter
transmission fluid/filter

Sep 02, 2010 | 2002 Toyota Corolla

1 Answer

Toyota corolla altis 2003, driver side power window is not working properly when using the auto button, if you close the window using the auto button it automatically closing but when it reaches to the end...

I had the same problem with my 2002 Altis. I found a solution after a lot of research and reading in the web.

1. Remove the power window motor from the regulator (mechanism).
2. Reconnect the power motor to the electronic controller(switches).
3. Perform "Auto Down" an wait until the motor stops.
4. Put a mark in the motor gear.
5. Perform "Manual Up" slowly until the gears rotates around 6 times but not greater than 10 times.
6. Remove the motor from the electronic controller.
7. Re-assemble whole power window assembly.

Apr 02, 2010 | 2002 Toyota Corolla

4 Answers

1992 geo metro

The check balls I put back in were slightly larger. You should be able to get them from any transmission shop or the Chevy dealer. I got my gasket from the Chevy dealer.

Jul 02, 2008 | 1992 Geo Metro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides