Cars & Trucks Logo

Related Topics:

Tere Lea Posted on Sep 13, 2013

How do you tell what size thread is on a tie rod for a 2002 gmc envoy?

1 Answer

A

Anonymous

Measure the outer diameter of the outer tie rod
threads & the thread pitch of the threads


If it appears to be a metric size,the thread pitch will
confirm that & you convert the diameter to metric
by dividing by .0395

5 Related Answers

Anonymous

  • 1 Answer
  • Posted on Dec 07, 2008

SOURCE: Inner tie rod 99 durango replacement

make sure if you do it youself you count how many turns it takes for your tierods to come off. it it makes it easy for me that way. also make sure you get a front end aligiment when your done

Ad

Anonymous

  • 341 Answers
  • Posted on Dec 29, 2008

SOURCE: Replace the thermostat on 2002 GMC Envoy

4.2L Engine the thermostat and the neck where the hose goes on is one unit $25 at autozone

  1. Remove the necessary coolant from the radiator.
  2. Remove the alternator, Loosen the outlet hose clamp at the thermostat housing. Remove the outlet hose from the thermostat housing.
  3. Remove the thermostat housing bolts.
  4. Remove the thermostat housing from the engine block.
  5. Clean all of the surfaces of the thermostat housing.
  6. Clean the sealing surface of the engine block.

Anonymous

  • 104 Answers
  • Posted on Mar 20, 2009

SOURCE: Need firing order diagram for 2002 gmc envoy

one, five, three, six, two, four

The plastic intake should have this sequence molded into it somewhere, and even the corresponding cylinder numbers in front of their respective holes. Have fun, and thanks for posting on Fixya.com

ddegroote

Dan De Groote

  • 35 Answers
  • Posted on May 26, 2009

SOURCE: need fuse box diagram 2002 gmc envoy

If I remember correctly if you look at the back side of the fuse cover, it should tell you what the fuses are. Also in the owners manual in the index, under fuses, it should give you a diagram of the fuse location for the acc. outlets. Good luck. The fuse should be a 20 or 25A fuse.

Anonymous

  • 353 Answers
  • Posted on Jul 27, 2009

SOURCE: 2002 gmc envoy shuts off when i turn on the ac whil ideling

If it does it when idling I would suspect an IAC motor (Idle Air Control). If it is opening too slowly the added air the motor needs will not be supplied fast enough and the engine will kill.

It could be other things also but this is where I would start.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Ball joint bolt fell out upper in 2007 GMC Envoy

Upper ball joint? That's not related to the job of replacing a tie rod or tie rod end. It's also not related to the brake job.

It's an '07 and it had a bolt-in ball joint? That's not factory - it's been replaced before.
0helpful
1answer

Are there 2 tie rod ends on front off 2002 envoy?

No, is the short of it, it must be broken, take it to a Front End specialist before something happens that hurt someone!!>>
0helpful
1answer

How to find out if the front axel is bad

Sounds like it could be worn cv joint assenbly which is the axle.
0helpful
1answer

How to replace the tie rod end

Tie rod ends are replaceable, whether the steering system is rack and pinion or parallelogram steering system.
f42-02.gif Parallelogram steering system mounts. Figure A - behind front suspension; and Figure B - ahead of front suspension. f42-04.gif A rack and pinion steering system. Tie rod ends are threaded to provide a means of adjusting toe. When a tie rod is replaced, measure the old tie rod assembly before disassembling it. An approximate toe-in adjustment can be made to the new one prior to installation. When removing the old tie rod end, count the number of turns it takes to remove it. Then, turn the new tie rod end onto its threads the same number of turns.
Some vehicles have tie rods that appear to be the same on both ends. The difference is in the threads. One end has left hand threads and the other has right hand threads. It is possible to install the entire shaft backwards (which will work). Mark the tie rod to identify the inner or ourter end before removing it.
Before tightening tie rod clamps, check to see that they are in good condition and are positioned properly so they can be clamped tightly. Before doing a front end adjustment, spray penetrating oil on the threads of the tie rods. Do this during the steering linkage inspection so the lubricant has time to soak in.
1helpful
1answer

When i use the key fob to lock the doors the back glass dont lock, ???????

This solution applies to models:
2002-2007 Chevrolet Trailblazer, Trailblazer EXT and Trailblazer SS
2004-2007 Buick Rainier
2002-2007 GMC Envoy, Envoy XL, and Envoy Denali
2002-2004 Oldsmobile Bravada
2005-2007 Saab 9-7x

Condition/Concern:
Rear liftgate glass will not lock when using the key fob or door switch unless the lock button is pressed a second time. All other doors will lock normally. This could be the result of the liftgate glass lock rod not adjusted correctly. This lock rod travels from the liftgate lock actuator to the glass release push-button cylinder.

Recommendation/Instructions:
Remove the inside rear liftgate trim panel. Disconnect the threaded lock rod clip at the end of the push-button glass release and rotate this clip 1 complete turn at a time making the lock rod longer. This will be the only threaded lock rod visible when the trim panel is removed and the liftgate is raised.
Note: For the rear glass to release, the rear liftgate latch must be in the closed position. For test purposes only, this latch can be made closed to make this lock rod adjustment.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.
1helpful
1answer

2002 gmc envoy xl front wheel bearing assy replace

take the wheel off,take the axle nut off,disconnect the spindle from the ball joint or joints, take the tie rod end out of the spindle and remove the spindle leaving the axle in the transmission. Now there is three bolts on the back of the spindle take theese out and beat the hub and bearing assy out. The new one wont be as hard to put in as the old one was to come out.
0helpful
1answer

I have a 2002 GMC envoy, when I come to a stop about 2 ft. from dead stop my front end thunks.

my envoy was doing this too, i went all through my brakes and it still did it, i noticed a bad tie rod end and after i changed it and had an alignment done i dont hear it anymore, so check tie rod ends for play and also check the sway bar end links
Not finding what you are looking for?

317 views

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

john h

Level 3 Expert

29494 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...