My drivers side low beam headlight will not work, high beams are okay. Changed the light bulb and the fuse is good. Any clues

Check the wiring on that light. Also check the bulb with a couple of wires to the battery, or swap the bulb left to right to make sure the new bulb is okay.

If fuse 31 is good, there may be a problem with the headlight control circuit board in the smart junction box.
http://www.revbase.com/BBBMotor/Wd/DownloadPdf?id=110641

I would check for the groundwire continuity

Driver side - dim low beams and no hi beam - Subaru Outback ...

www.subaruoutback.org > ... > General > Electrical & Electronics

Oct 11, 2014 - Hi everyone, My drivers side headlights are dim on low, (car has separate bulbs ... When the headlight switch is turned ON, but for low beams, ...

Driver-side Low beam Not Working (electrical issue not bulb ...

www.hummer4x4offroad.com/.../showthread.php?...Driver-side-Low-be...

Mar 12, 2015 - 10 posts - ‎4 authors
The high beam continues to work on both sides...I pulled the Driverside headlamp fuse and then both left and right beams lit up but very dim.

High beams ok, but not low beam - one side only - TDIClub Forums

forums.tdiclub.com > ... > VW MKIV-A4 TDIs (VE and PD)

Jan 23, 2014 - My driver's side lights are working fine - high and low beams. ... But it definitely looks like the big lamp on the driver's side gets brighter when ..... Drivers side headlight is very dim on low beam and goes out when on high beam ...

Dim driver's side headlight (low & high beam) - GrandAmGT.com Forum

www.grandamgt.com > ... > Technical Q&A

Dec 11, 2002 - 6 posts - ‎4 authors

HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

try the fuses or wire fuse links , the only other thing in the circuit is the wires broken or the light low switch is bad

check low beam fuse when switched on if it has voltage registering across the fuse ,if there is voltage across the low beam RHS fuse then it is possibly a pinched wire from the headlight running back towards inside of the car

check for a damaged wire for the low beam. Also wouldn't hurt to check the ground wire as the high beam will try and ground through the low beam but not visa verse

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

check the bulbs first and also the fuses theres a fuse for each side and for low and high beams, start there, good luck.

it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!