"04 Chevy Malibu: ignition switch stuck in off, key is incerted an removed easily, but will not turn, all solutions remove switch that i have found thus far require switch to be in run position for removal

IGNITION KEY WILL NOT RELEASE

It can be faulty ignition lock cylinder. I suggest to wiggle the steering wheel a bit and see if the key gets released out. If that is not helping then first turn steering wheel to right and try removing the key, or next turn steering wheel to left and see if you can remove the key.

----------

Spray wd-40 in the ignition key hole and let it remain there for few minutes, after that once again try to remove the key and see if that helps.

---------

But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.

-----------

For more troubleshooting on these types of issues, I suggest you to refer the help links mentioned below. Its the accurate solutions mentioned in it. That will help you to narrow the problem: -----

Click the link below: ------

-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html

---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html

------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html

-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html

--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html

-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?

http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html

-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html

-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html

------------------

These will help.

Thanks.

It can be faulty ignition lock cylinder.I suggest to wiggle the steering wheel a bit and see if the key gets released out.If that is not helping then first turn steering wheel to right and try removing the key,or next turn steering wheel to left and see if you can remove the key.
----------
Spray wd-40 in the ignition key hole and let it remain there for few minutes,after that once again try to remove the key and see if that helps.
---------
But if that is not helping then ignition lock cylinder has to be removed out and key has to be manually removed.
-----------
For more troubleshooting on these types of issues,i suggest you to refer the help links mentioned below.Its the accurate solutions mentioned in it.that will help you to narrow the problem:-----
Click the link below:------

-----------

1999 Toyota Camry: Key Will Not Come Out Of Ignition?

http://whatisbyme.blogspot.in/2012/05/1999-toyota-camry-key-will-not-come-out.html
---------------

2001 Toyota Tacoma: Ignition Locked?

http://technoanswers.blogspot.in/2012/04/2001-toyota-tacoma-ignition-locked.html
------------

Ignition Switch Will Not Turn Off?

http://schematicsdiagram.blogspot.in/2012/04/ignition-switch-will-not-turn-off.html
-----------

Car will not turn the ignition to start?

http://technoanswers.blogspot.com/2012/01/car-will-not-turn-ignition-to-start.html

-----------

Ignition Key OFF but engine still running?

http://howtobyme.blogspot.in/2012/03/ignition-key-off-but-engine-still.html
--------------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html-----------

Ignition locked up on Mercury Villager?

http://technoanswers.blogspot.in/2012/01/ignition-locked-up-on-mercury-villager.html-------------

Key won't turn in the ignition on Toyota land cruiser?

http://technoanswers.blogspot.in/2012/02/key-wont-turn-in-ignition-on-toyota.html

-------------------

How to remove ignition switch on VW Car models?
http://schematicsdiagram.blogspot.com/2011/12/how-to-remove-ignition-switch-on-vw-car.html
-------------

How to Replace Ignition Switch on Chevrolet Caprice Classic?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-ignition-switch-on.html

-----------------

1995 Ford Taurus: Ignition switch not turning OFF?

http://repairhelpcenter.blogspot.in/2012/06/1995-ford-taurus-ignition-switch-not.html
-------------

Ignition Problem Troubleshooting

http://whoisbyme.blogspot.in/2012/07/ignition-problem-troubleshooting.html
------------------These will help.Thanks.

I have a 2001 malibu the the key will not turn completely off(sometimes).
the key switch is on the dash and the shifter is on the middle console. there is a cable going from the switch to the shifter.
I found that if I disconnect the cable from the shifter and push the cable towards the switch, then leave it disconnected I don't have the key stuck issue and the switch will go all the way to the OFF position.
also there is a cylinder connected to the shifter, mine has had the wires cut(from a previous owner) you may need to unplug it.

disconnect negative battery terminal, remove trim around switch, be carefull it will easily break, it pulls out, it is held on dash by clips they will pull out. remove the 2 screws that hold in switch. push the switch in about 1 inch to clear the mounting bracket, then lift it out.

You have to have the key coded with the ignition switch at a lock smith,or the dealer.

1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

PROGRAMMING
Method One
Sit in driver's seat
Close all doors
Press and HOLD UNLOCK button on door lock switch.
Insert and remove ignition key twice. Do NOT turn ignition switch
Insert ignition key a third time and leave it in the ignition switch. Do NOT turn ignition switch
Release door lock switch.
A chime will sound three times indicating remote programming active
Press and HOLD the LOCK and UNLOCK buttons on each remote for 5 seconds
A chime will sound twice for each remote: indicating successful programming
Remove the key from the ignition switch to exit programming
Method Two
Remotes can be programmed using diagnostic equipment.

On this car there is a cable that is tied into the shifter, so you have to turn the keep to be able to take it out of gear. Its all in 1 big housing. Usually to remove the ignition cylinder it has to be in the run position and you push a little key down to remove it. Since your key won't turn you have to figure out a way to do it.However once you replace the ignition cylinder your shifter will move and you will be able to start the car. To get to the ignition switch/cylinder you have to remove the molding around the instrument panel and then the instrument cluster. Then you can unbolt the assembly in the front with a 10mm socket. lift the assembly up and now you have access to change it out. Hope this helps.

If you just need an ignition key, take your title and ID to a Chevy dealer. They may be able to provide you with new keys.

I have 07 Pontiac Grand Prix, the wrong key was inserted into the ignition the other day. Now when I try to use the correct key it will not insert completly in the ignition, goes in until last 1/4in of key. Im stuck, I bought the new lock cylinder but how do I get the old one out? I cant get the key to insert all the way so I cant get it to the "On" position, it will not turn at all. The key that was inserted in error is whole and nothing is missing it seems like there is something stuck. Any help would be appreciated...