2004 Chrysler Sebring Logo
Posted on Apr 14, 2009

2004 Chrysler Sebring- Left turn signal problems

I have a 2004 Chrysler Sebring LTD Coupe. When I turn the headlights on the Left rear signal lamp stays on, when lights are off and I use the left turn signal, the hazards work and all the lights on the inside blink.

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 2 Answers
  • Posted on Apr 14, 2009
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.

Mayor:

An expert whose answer got voted for 2 times.

Joined: Apr 14, 2009
Answers
2
Questions
0
Helped
1378
Points
7

Sounds like a short in the wiring or fuse panel. As new as it is, I would suggest a mechanic as troubleshooting wiring in newer cars is not only difficult, but also dangerous. Many a shade-tree mechanic has set off the airbags that way!

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers

Windshield wipers stop working when the defroster is on

The only thing they have in common is the ignition switch.
0helpful
1answer

Can the 2005 Chrysler Crossfire Limited Coupe automatically turn on the low beam head lamps at night?

No. It has auto lamps.all newer vehicles have them. Some you can turn off. You have to have the light switch in the dash. If it is in the turn signal switch/ column. Your out of luck.
1helpful
1answer
0helpful
2answers

My 2004 chrysler sebring is having turn signal problems. The left turn signal does not work when head lamps are off, and when head lamps are on they flash simultaneously with right signal as if hazard...

Have you checked for any bad bulbs that need to be replaced. Check the bulbs and replace if needed. If it's not that maybe be a bad ground wire connection or bad switch. Hope it's just a bulb. If it's a bad ground that may be harder to see but check the wires also for any damage from rubbing. If you see a ground connector to the body or frame and it's covered in rust. That may be your problem. Clean the area from rust and reattach and try the lights again. A sign a ground is bad. The lights may be dim in that area the lights don't work.
0helpful
1answer

Left rear turn signal light replacment

Hello,

To replace the left rear turn signal light, please follow the steps below:
  1. Open the rear hatch of your van.
  2. There are two black button like protrusions behind the hatch next to the turn signal lamp.
  3. Pry these out and remove lens.
  4. Replace bulb.
  5. Then reverse the process th reassemble the hatch back together.
Hope this helped. Thank You for using FixYa!!!
3helpful
2answers

Tire specs for 2001 chrysler sebring

HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16
1helpful
2answers

I can't locate the fuel filter on my 2004 chrysler sebring 6 cyl coupe (3000).

I would check if it is in the gas tank on that model. you can go to your local parts store and they should be able to inform you of this.
1helpful
1answer

How do I replace the headlight assembly on a 2006 sebring?

  1. Remove the front bumper cover
  2. Remove the upper headlight housing mounting bolt and pushpin
  3. Remove the lower headlight housing mounting bolts
  4. Pull out the headlight housing assembly and disconnect the electrical connector.
Its pretty easy. Just raise the hood, see the two silver 8mm cap screws on top of the cross member that supports the radiator and fan assembly. Two screws on each side above the headlight housings. The outer screw is right next to the corner of the fender when the hood is raised. Remove the two screws, then the headlight assembly is loose. Just gently pull the headlight assembly forward enought to see the three lamp socket holders on the back side of the headlight assembly. From the outside corner to the inside are first, the parking turn signal, then the low beam lamp and finally the last, the high beam lamp. To remove the lamp socket, push the small plastic locking tab and turn the socket assemby counter clockwise about a half turn and remove the lamp. Now you can replace the lamp and install it back the same way you took it out. Don't touch the new lamp glass with your bare fingers. Oil from you skin will absorb into the glass causing the glass to turn dark and shorten the lamp life. 
0helpful
1answer

Turn signals, rear deforst, and wipers stopped working

this sounds like your body control module is bad.
1helpful
2answers

Driving lights on chrysler sebring convertible

The roatating knob that turns on the headlight pulls out to turn on the fog lights, but only pulls out when the headlights are on,
Not finding what you are looking for?

550 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...