2004 Chrysler PT Cruiser Logo
Posted on Apr 13, 2009
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

TIEROD PROBLEMS MY MECHANIC SAYS ,from the occasional knocking noise when turning Left and RIght of my 2004 PT cruiser , I have a loose Right outer tierod, he says probably needs both. you can replicate the noise even sitting still, turning left then right ...repeat if you want. Can i put them in myself, then get front wheel alignment.?

1 Answer

Antipode

Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

Hot-Shot:

An expert who has answered 20 questions.

  • Expert 51 Answers
  • Posted on Apr 13, 2009
Antipode
Expert
Level 2:

An expert who has achieved level 2 by getting 100 points

MVP:

An expert that got 5 achievements.

Governor:

An expert whose answer got voted for 20 times.

Hot-Shot:

An expert who has answered 20 questions.

Joined: Apr 13, 2009
Answers
51
Questions
0
Helped
21860
Points
137

It's not recommended that you replace them yourself if you haven't at least watched someone else replace one before. Often they require use of a torch just to loosen them up, and it's nearly impossible to get the new tie rod ends where the old ones were just by eyeballing it. Even just driving it from your house to the mechanic afterwards could cause significant enough tire wear to throw off an alignment.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

2006 pt cruiser making scraping noise when wheel turning to the right

is it a scraping noise or a clicking noise. a scraping noise could indicate a brake noise when turning have the brakes checked in the front. if its a clicking noise only when turning to the right then you may have a bad cv joint on the right half shaft. replace the half shaft assembly.
0helpful
1answer

2002 pt cruiser making a left turn clunking noise from front end. Also sounds like a creaking noise underneath the vehicle. Mechanic replaced the front bushings and control arm. Still have problem. Could...

I know this website www.reliable-store.com that i get manuals from, and they have all models online that solve all simple/technical problems like professionals

I also brought for my 1989 BMW, such old model, they had it and it was very good manual. Go ahead, I bet.
1helpful
2answers

I'm having the same exact problem as cpurdey with my 2004 Mazda MPV. My mechanic is quite certain it is not the wheel bearing or hub but seems to think it's a bearing in the transmission. Is...

If it gets worse as you're turning right, but not left - Most definitely a wheel bearing on the right side. The right turn puts more stress on the right wheel - louder noise - turn left and release the stress - no noise. You can also lift the vehicle up on a jack and listen to the wheel and hear the bearing in the hub making noise.
0helpful
1answer

Just had the timing belt changed for my 2004 pt cruiser and the engine is making load rattling noise.

Hopefully something is just loose and rattling around. The bad alternative is that the timing belt job was botched. I would not drive the car , get the mechanic to come over and find the problem , or he can tow it back to his shop at his expense.
1helpful
1answer

2004 PT Cruiser: Windshield water spray is very

CHECK THE SUPPLY TUBES FROM THE PUMP TO THE SPRAY HEADS. SOME TIMES FINE PARTICALS OF DIRT WILL STOP THESE UP REMOVE THE HOSE FROM UNDER THE HOOD AND USE COMPRESSED AIR AND BLOW FROM THE SPRAY HEADS BACK TO THE OPEN HOSE TO CLEAN OUT THE DIRT IF THIS DOSN'T WORK LEAVE THE HOSE OFF AND TRY THE WASHER WITH OUT THEM HOOKED UP SEE WHAT KIND OF FLOW YOU GET FROM THE PUMP IF IT IS VERY LOW THE PUMP IS BAD
0helpful
2answers

SUSPENSION-03 pt cruiser touring

A banging noise when going over bumps? I'd guess the lower control arm bushings are worn. This is relatively common, and would exhibit this symptom.
1helpful
1answer

My 200 mazda mpv van is makin a knocking sound when i turn

Have your front outer C/V joints checked. ( left & right driveshafts outer joints get dry or worn causing a knocking or racheting type noise. ) hope this helps
3helpful
4answers

2002 Mazda Protege 5: I am having a knocking sound coming from my front right of the car.The noise is most noticable when turn right with speed. The noise is also there when driving straight but not all...

I would check the sway bar linkages, they are usually the first to go, and they are only $40. Its an easy 'do it yourself' project, remove the old one with torches or a grinder (with a small cutting wheel). You can also use a vise grip and sockets but it takes longer.

You can't tell these are damaged until you remove the part. I change mine every 100 000km or so.
Not finding what you are looking for?

258 views

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...