Engine cranking but no start

To remove key (lock position), the transmission needs to be in PARK.

To start (engine crank), the transmission must be either in PARK or NEUTRAL.

Try apply parking break, put transmission in neutral and turn ignition key. If engine does not crank, turn and hold key in start position then move transmission selector to see if there is a transmission select position where it does crank.

You have know idea how the starting system works , an with the engine light on your best bet would be to have it towed to a qualified repair shop .
When the ignition switch is turned to the Start position, the body control module (BCM) receives battery voltage on the ignition 1 voltage circuit, and less than 5 volts on the off/run/crank voltage circuit. The BCM supplies voltage to energize the RUN/CRANK Relay 32. The BCM sends a high speed GMLAN serial data message to the engine control module (ECM) that the key is in the start position. The ECM receives the message from the BCM, and also receives a serial data message from the transmission control module (TCM) containing the shift lever position. If the shift lever is in Park or Neutral when ignition switch is turned to Start, the ECM supplies voltage to the START Relay 31. The START relay supplies voltage to the S terminal of the starter solenoid, through the 30 A STRTR Fuse 26, in order to crank the engine.

Could be a number of thing's , can you do automotive electrical testing ? Do you know if starting is PCM / ECM controlled or BCM controlled ? Do you know what these are ? BCM - body control module , PCM/ECM - engine computer !
Moving the ignition switch to the START position sends a 12-volt signal to the engine control module (ECM)/powertrain control module (PCM) Crank Request circuit. The ECM/PCM verifies that the transmission is in the PARK or NEUTRAL position. With the transmission in Park, voltage flows through the Park/Neutral position switch and feeds the starter relay coil. The PCM then grounds the control circuit of the starter relay. When the starter relay is energized it allows battery positive voltage to the starter solenoid S terminal. On some vehicles the starter will continue to crank the engine with the key released until it starts or the crank command has timed out to prevent excessive heat build up in the starter circuitry or the ECM/PCM receives an engine run flag.
Circuit Description (BCM Controlled)
Moving the ignition to the START position signals the body control module (BCM) that engine crank has been requested. The BCM verifies that theft is not active and sends a serial data message to the powertrain control module (PCM) requesting engine start. The BCM also energizes the RUN/CRANK RELAY. When the RUN/CRANK RELAY switch side closes, and the vehicle is in Park or Neutral or with the clutch is fully depressed, if equipped, supplies voltage to the starter relay coil. The PCM verifies the transmission is in Park or Neutral and the clutch is fully depressed, if equipped. The PCM will then ground the control circuit of the starter relay, closing the switch supplying voltage to the starter solenoid. On some vehicles the starter will continue to crank the engine with the key released until it starts of the crank command has timed out to prevent excessive heat build up in the starter circuitry or the PCM receives an engine run flag.
Do you know what a park neutral safety switch is ? What do you mean key stuck in ignition ? Can't turn the key to off position , or you can an the key will not come out ?
Your best bet , take it to a qualified repair shop .

I want to see if i catch your drift ! When you turn the key in the ignition switch to start , nothing happens ? Have you tried moving the gear slector to the neutral position to see if it starts then ? Park neutral safety switch problem , maybe .
Here is a description of how it works or how it's suppose to work .
Circuit Description (ECM/PCM Controlled)
Moving the ignition switch to the START position sends a 12-volt signal to the engine control module (ECM)/powertrain control module (PCM) Crank Request circuit. The ECM/PCM verifies that the transmission is in the PARK or NEUTRAL position. With the transmission in Park, voltage flows through the Park/Neutral position switch and feeds the starter relay coil. The PCM then grounds the control circuit of the starter relay. When the starter relay is energized it allows battery positive voltage to the starter solenoid S terminal. On some vehicles the starter will continue to crank the engine with the key released until it starts or the crank command has timed out to prevent excessive heat build up in the starter circuitry or the ECM/PCM receives an engine run flag.
Circuit Description (BCM Controlled)
Moving the ignition to the START position signals the body control module (BCM) that engine crank has been requested. The BCM verifies that theft is not active and sends a serial data message to the powertrain control module (PCM) requesting engine start. The BCM also energizes the RUN/CRANK RELAY. When the RUN/CRANK RELAY switch side closes, and the vehicle is in Park or Neutral or with the clutch is fully depressed, if equipped, supplies voltage to the starter relay coil. The PCM verifies the transmission is in Park or Neutral and the clutch is fully depressed, if equipped. The PCM will then ground the control circuit of the starter relay, closing the switch supplying voltage to the starter solenoid. On some vehicles the starter will continue to crank the engine with the key released until it starts of the crank command has timed out to prevent excessive heat build up in the starter circuitry or the PCM receives an engine run flag.

Hi there:

When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.


Just scanned the computer and send us code number find it.

Hope helps.

P0335 - Crankshaft Position Sensor A Circuit Malfunction

The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

Symptoms:
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include:
* Vehicle may not start (see above)
* Vehicle may run rough or misfire
* MIL illumination

Causes: A P0335 "check engine light" code could be caused by:
* Damaged CKP sensor connector
* Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
* Sensor output open
* Sensor output shorted to ground
* Sensor output shorted to voltage
* Failed crank sensor
* Broken timing belt
* Failed PCM

Possible Solutions:
1. Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
2. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
3. If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
4. If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Test it and keep us updated.

Hello it is not easy to use a computer with a 4 year old constantly trying to get your attention.Anyhow i said disconnect your battery wait 5 minutes to reboot the computer i have gone through your situation a dozen times if it doesn't start it should trip your check engine light and you will be able to scan and retrieve keep me posted.John

i would  check the crank position sensor. if this part is bad the cars computer will not recive signal to send fuel or spark.

check to see if starter relay clicks while turning key to start position,if it does click check to see if voltage is reaching starter solenoid..if voltage at post on starter solenoid,but not cranking replace bad starter..(starter relay is located in fuse panel under hood..place finger on it while someone turns key to crank position ..should feel light click)

Two things that may help you or them find the problem.

When it does this what is anti-theft light doing? Normal operation is when you turn key on it should come on for a couple of secs then turn off.If it starts flashing rapidly when key is in the on position then it does not see your key and will not start.

2nd thing is when it cranks but will not start does the check engine light come back on while cranking after about 10 secs? When you turn key to on position the check engine light should come on,as you start cranking the engine is should go out but as engine is cranking it should come back on while it is cranking within 10 secs. If it does not then the computer is not seeing the crankshaft position sensor and this is your concern. This will usually not set a trouble code either so it makes it hard to diagnosis unless it does it while they are checking it.