- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
google how to program fob for 2011 chevy malibu for more info
On the Chevy key fob, press and hold the "Unlock" and "Lock" buttons at the same time until you hear the door lock and unlock again. This means you're all set. Re-insert the programmed key back into the ignition to the "On" position to finish the Chevy key fob programming process
Transmitter Programming Procedure
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Good luck
Close all the vehicle doors. Insert the ignition key into the ignition lock cylinder. Press and hold the DOOR unlock switch. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter. Repeat the previous step to program up to four transmitters. - See more at: http://theandrewhughes.com/2007/05/how-to-program-most-gm-key-fobs/#sthash.6oXk0NFT.dpuf
try this procedure, close all doors, insert key into ignition switch,press and hold door unlock switch,turn ignition switch from on to off twice, release door unlock switch,doors will lock then unlock to confirm programming mode.now simultaneously press and hold the lock and unlock buttons of the first remote transmitter after approximately 15 seconds doors will lock then unlock to confirm remote transmitter programming. if all fails to work take vechicle to dealership, they will have to use diagnostic equipment to reprogram remote.
stick key in driver door lock and unlock it. If that works, now see if the remote will unlock the door or doors..i remember reading in an owners manual once where you can program which doors open and close by they way you press and hold down the two main buttons, also after a battery change in the remote, i think, but not sure, i did this on a blazar i once owned... the owners manual said, that you had to be within 20 feet and press and hold down both buttons till it makes the arming sound.... Can i get some feedback cause im curious..thanks.
Programming When Key added or replaced. System malfunction. How Obtain all keys. A maximum of 3 keys can be programmed. Close all doors and boot/tailgate. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press key lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press key lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press key lock or unlock button. Within 10 seconds: Press lock or unlock button of first key. System should now lock or unlock vehicle. Press lock or unlock button of second key. System should now lock or unlock vehicle. Press lock or unlock button of third key. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed keys. NOTE: If less than 3 keys are to be programmed, remove ignition key after programming last key.
Transmitter Programming Procedure Close all the vehicle doors. Insert the ignition key into the ignition lock cylinder. Press and hold the door unlock switch. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. Release the door unlock switch. The doors will lock and unlock to confirm the program mode. Press and hold the LOCK button and the UNLOCK button simultaneously on the transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of the transmitter. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode. Operate the transmitter functions in order to verify correct system operation. Good luck
You may program up to 4 transmitters, using following procedure:
Transmitter Programming Procedure (No Tools Required) Close all the vehicle doors. Insert the ignition key into the ignition lock cylinder. Press and hold the door unlock switch. While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. Release the door unlock switch. The doors will lock and unlock to confirm the program mode. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter. Repeat the previous step to program up to four transmitters. Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode. Operate the transmitter functions in order to verify correct system operation
Program your factory keyless entry functions For 2001+ Tacomas equipped with a factory alarm or keyless entry, here are some programming options that allow you to adjust the way your locks work. The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
Open the driver's door. Remove the key from the ignition switch.
(Complete these steps within 40 seconds)
Insert the key into and remove it from the ignition switch 2 times. (IN - OUT - IN - OUT)
Close, then open the driver's door 2 times. (SHUT - OPEN - SHUT - OPEN)
Insert the key into and remove it from the ignition switch 1 time. (IN - OUT)
Close, then open the driver's door 2 times. (SHUT - OPEN - SHUT - OPEN)
Insert the key into the ignition switch and leave it in.
Close the driver's door.
Turn the key from LOCK to ON 4 times, ending at LOCK (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
Wait for the locks to stop, then remove the key from the ignition switch.
On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
[For all doors unlock] press and release the UNLOCK button.
[For driver door unlock] press and release the LOCK button.
Open the driver's door. The programming is complete. If programming did not occur, start over.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously
on one keyless remote. After a delay of approximately 15 seconds, the
doors will lock and unlock to confirm the programming of that
transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
×