The ignition locking switch isn't unlocking, how to replace?

If your 2014 Frontier's steering and ignition are locked and wiggling the wheel while turning the key does not unlock it, there are a few possible causes and solutions you can try:

1. Dead battery: If the battery is dead or low on power, it can cause the steering wheel lock to engage and prevent the key from turning. Try jump-starting the vehicle or replacing the battery to see if that resolves the issue.
2. Faulty ignition switch: The ignition switch may be faulty and not responding to the key, preventing it from turning. You may need to replace the ignition switch to resolve the issue.
3. Damaged steering column: The steering column may be damaged or worn, preventing the steering lock from disengaging. In this case, you may need to replace the steering column or have it repaired by a qualified mechanic.
4. Malfunctioning lock cylinder: The lock cylinder itself may be malfunctioning or damaged, preventing the key from turning. You may need to replace the lock cylinder to resolve the issue.

Cmon, if you use a key it would be simplier. Only the key can unlock steering wheel and ignition regardless of the car

I had a similar problem with my 2004. I changed the cylinder. Its amazing how much of it is plastic. Over time it wears. You will have to disable the Air bag system and pull the steering wheel. You will need a steering wheel puller and another tool to push it back on. You also have to transfer a part from the original switch to the new one so don't immediately chuck the old one. Afterwards you have to reset the anti theft.

Replace the switch and turn the key it should unlock it

Its going to be inside the steering column near the ignition switch. When you turn the ignition it unlocks the steering lock. You can't really manually unlock it unless you break the lock system

If you any other spare key, try with that key and see if it turns the ignition to unlock position.Try to turn the steering wheel to left and key to right side and try turning key to left an steering wheel to right side, try both ways and see if the key unlocks ignition.If that is not helping then try to wiggle the steering wheel and then insert key to unlock ignition.If that is also not helping then get wd-40 spray and spray the lubricant into key hole, and then let the spray remain there for few minutes then insert key in the key hole and see if it unlocks the ignition.------ If not then its problem with tumblers in the ignition switch, it has to be checked.For that ignition switch has to be removed and inspected.If ignition switch is inspected ok, then ignition key lock cylinder is faulty, it has to be replaced.Once the ignition switch is removed, the key lock cylinder can be accessed.----------- Getting this troubleshooting tried and this possibilities checked will help, thanks.Helpmech.

This is not an easy repair due to anit theft requirements. need to chisel off bolts.

Section 11-04: Steering Column 1997 Probe Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000
Ignition Switch Lock Cylinder Removal

1. Remove the steering wheel (3600). Refer to the procedure in this section.
   

1. Remove the four lower steering column shroud screws.
   
   
   
   
   

1. Separate the upper and lower steering column shrouds.
   

1. Remove the ignition switch lock cylinder illumination miniature bulb from the lower steering column shroud.
   

1. Remove the upper and lower steering column shrouds.
   

1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal and installation procedure.
   

1. If equipped, remove the ignition/shifter interlock cable screw.
   

1. Disconnect the ignition/shifter interlock cable (3F719) from ignition switch lock cylinder (11582).
   

1. Use a chisel to remove the two ignition switch lock cylinder bolts.
   

1. Remove the ignition switch lock cylinder from the steering column.
   

1. Disconnect the ignition key reminder switch electrical connector.
   

1. If necessary, remove the ignition key reminder switch.
   
   
   
   
   

Installation
NOTE: Use new ignition switch lock cylinder bolts. Tighten the bolts until the bolt heads break off. Check for proper ignition switch (11572) operation.

To install, reverse the removal procedure.

i have a 1997 honda accord and i need the radio code for it. my serial number is M96G146085

lock cylinder removal

Section 11-04: Steering Column 1996 Escort, Tracer Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Lock Cylinder Removal

1. WARNING: THE ELECTRICAL CIRCUIT NECESSARY FOR DRIVER SIDE AIR BAG MODULE DEPLOYMENT IS POWERED DIRECTLY FROM THE BATTERY. TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BATTERY GROUND CABLE MUST BE DISCONNECTED PRIOR TO SERVICING OR REPLACING ANY DRIVER SIDE AIR BAG MODULE SYSTEM COMPONENTS.
   Remove the steering wheel (3600). Refer to the procedure in this section.
   

1. Remove the multi-function switch (13K359). Refer to Section 11-05 for the removal procedure.
   

1. Disconnect the ignition switch electrical connector.
   

1. Remove the ignition/shifter interlock cable mounting bracket bolt and position the ignition/shifter interlock cable mounting bracket and the ignition/shifter interlock cable (3F719) aside.
   
   
   
   
   

1. Remove the four steering column upper mounting bracket bolts and lower the steering column (3C529).
   

1. Use a hammer and chisel to make a groove in the head of each of the two ignition switch lock cylinder bracket bolts.
   
   
   
   
   

1. Remove the two ignition switch lock cylinder bracket bolts with a screwdriver and discard the bolts.
   
   
   
   
   

1. Remove the ignition switch lock cylinder and the ignition switch lock cylinder bracket.
   

Installation

1. Position the ignition switch lock cylinder and bracket and install two new bolts, tightening them only enough to hold the ignition switch lock cylinder in position.
   

1. With the key in the ignition, verify the operation of the ignition switch lock cylinder. If necessary, reposition the ignition switch lock cylinder until it operates properly.
   

1. Tighten the ignition switch lock cylinder bracket bolts until the bolt heads break off.
   

1. Position the steering column and install the four steering column upper mounting bracket bolts. Tighten the steering column upper mounting bracket bolts to 9-14 Nm (80-124 lb-in).
   

1. On vehicles equipped with tilt column, remove the upper mounting bracket retaining pin.
   

1. Position the ignition/shifter interlock cable mounting bracket and install the bolt. Tighten the ignition/shifter interlock cable mounting bracket bolt to 4-6 Nm (35-53 lb-in).
   

1. Connect the ignition switch electrical connector.
   

1. Install the multi-function switch. Refer to Section 11-05 for the installation procedure.
   

1. Install the steering wheel. Refer to the procedure in this section.
   

1. Inspect the shift interlock system. Refer to Section 07-05 for the procedure.
   

Step1 Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them. Step2 Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft. Step3 Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column. Step4 Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out. Step5 Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder. Step6 Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.