4 lo working, 4 hi stopped working , A4WD never worked

Some vehicles have a actuator in the transfer case that the lever pushes against to engage 4x4.

It could be a junk switch or it could be bad contacts inside the transfer case motor.. Does the transfer case switch to the selected gears? Everytime? If so, you might try another switch. If it does the same, I would say the motor contacts are bad. Replace the motor if you want the lights, But I personally wouldn't do it until the motor quit switching gears. They're not cheap.

Switch may be bad. Change switch should fix it.

More than likely it is the switch alot of electric 4-wheel drive switches have been known to go bad from lack of use

On these issue, there are few solved help links for troubleshooting the issue easily.-------

Click the link below: ---

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

-----------

4X4 Truck makes roaring noise in the front end?

http://schematicsdiagram.blogspot.com/2012/01/4x4-truck-makes-roaring-noise-in-front.html

-------------

Car will not go into 4WD high or 4WD low?

http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html

--------------

No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

------------

4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

----------

4WD light is flashing and beeping? NO 4WD high?

http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html

----------

2002 Jeep Wrangler: 4WD Idiot Light is ON?

http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html

----------

Traction control switch will not engage on 4WD High or Low

http://whoisbyme.blogspot.com/2012/10/traction-control-switch-will-not-engage.html

-----------

4WD light flashing and 4WD will engage after few minutes

http://repairhelpcenter.blogspot.com/2012/10/4wd-light-flashing-and-4wd-will-engage.html

------------

2008 Toyota Tundra: 4x4 Wheel Drive Light is Flashing?

http://technoanswers.blogspot.in/2012/05/2008-toyota-tundra-4x4-wheel-drive.html

----------

4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

-------

4x4 will not engage on Ford F150?

http://technoanswers.blogspot.in/2012/02/4x4-will-not-engage-on-ford-f150.html

-------------

Dodge Ram 4x4 light keeps flashing

4X4 LOW LIGHT IS FLASHING ON DASH

http://technoanswers.blogspot.in/2012/09/dodge-ram-4x4-light-keeps-flashing.html

----------

Ford 4x4 front wheels will not engage?

http://technoanswers.blogspot.in/2012/02/ford-4x4-front-wheels-will-not-engage.html

-------------

These details will help.

Thanks.

The actuator under the battery runs the engagement of the front Diff .If 4 - wheel low is working and high is not then that is a linkage adjustment problem at the transfer case or a internal problem with in the transfer case not the transmission . Those transfer case are not that expensive from a salavage yard if that ends up being your problem and they are not that hard to change ... Alot easier then the transmission

What do the lights on the 4x4 selector switch do when you switch to A4WD or $HI or 4LO positions? Do they blink and revert to previous selection? Has the Transfer Case fluid been changed at 50K intervals?
There are actuators on the Transfer Case and Front Differential that control the application of power to the front wheels. These actuators are controlled by the TCCM (Transfer Case Control Module). It takes a qualified 4 wheel drive technician to diagnose these systems.

4 wheel drive does not engage on a 2004 toyota tundra

Just to clarify, the "transmission" is not stuck in 4-Lo. It is the "transfer case" that is attached to the transmission that actually engages the 4-Hi and 4-Lo modes. To properly shift your vehicle into 4-Lo, you know that you have to shift the transmission into neutral and slow down to less than 5 mph. Once your vehicle slows down to this range, your can switch your transfer case into 4-Lo mode. Due to the inner workings of the transfer case, the actual shift into 4-Lo may take a few seconds to complete. This is normal and does not signify that there is an issue. All transfer cases that have 4-Lo mode will act this way regardless of the make or model. To make a long story short, to shift out of 4-Lo you must follow the same steps that you took to shift into 4-Lo, just in reverse order. Switch the transfer case to 4-Lo mode if it isn't already there. Slow down to less than 5 mph (your vehicle must be moving, though). Then, shift your car into 4-Hi or 2WD. Give your vehicle several seconds to complete the shift. The transfer case indicator light will flash until it is complete. When it does complete the shift into the new gear mode, you will most likely hear a "clunk" (the range sleeve inside the transfer case disengages from its mating spline) from under your car. Again, any transfer case with 4-Lo (regardless of make or model) will exhibit this same noise. This should help you get out of 4-Lo. It is good practice to shift your car into and out of 4-Lo at least a few times each year to keep all of the splines free of corrosion and build-up. Based on the age of your vehicle, your transfer case may also need a complete flush and some new transmission fluid. Hope this helps.

check the wires on the switch. pop off the middle dash panel. ( the one that goes over the radio and climate controls. the switch will be in the left side. check the wires to make shure they are not loose or corroded. Most likely your problem is the actuator needs replaceing. One way to see would be to turn on switch to 4hi and lightly tap on the actuator arm. do not hit it hard enough to break anything!!!