P0335 I changed an engine to 2004 mazda 6, and now the engine don't spark, I got code P0335 which mean crankshaft ciruit malfunction. How I fix this problem?

P0335 = Crankshaft position (CKP) sensor - circuit malfunction.
There is an issue with the Crankshaft position sensor or the wiring to it. Get a Good Auto electrician to test the circuit and see how much it will cost to change the actual sensor.

the sensor may be good its the circuit code which means can be a wiring /connection problem not just the sensor the following link is courtesy of obd-codes.comP0335 - Crankshaft Position Sensor A Circuit Malfunction OBD-II Trouble Code Technical Description Crankshaft Position Sensor A Circuit Malfunction What does that mean? The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set. Symptoms NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination Causes A P0335 "check engine light" code could be caused by: Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM Possible Solutions Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault. This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.

Read more at: http://www.obd-codes.com/p0335
Copyright OBD-Codes.com
http://www.obd-codes.com/p0335

Error Code: P0335
Description:
Crankshaft Position (CKP) Sensor - Circuit Malfunction
Possible Cause:
Wiring.
Crankshaft position (CKP) sensor.
Engine control module (ECM).

code p0335 refers to crankshaft position sensor ( CKP)-circuit malfunction === causes --wiring---CKP sensor---ECM Replace the sensor.

P0335 stands for Crankshaft Position Sensor Malfunction change the sensor and the car should run great but in order to remove the check engine light you have to hook it up to a scann tool and press erase codes

DTC P0335 - Crankshaft Position Sensor A Circuit Malfunction
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

A P0335 "check engine light" code could be caused by:
Damaged CKP sensor connector
Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
Sensor output open
Sensor output shorted to ground
Sensor output shorted to voltage
Failed crank sensor
Broken timing belt
Failed PCM

If you need additional details about test and solutions, just contact us in the Code Link.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer. Thank you for using Fixya, and have a nice day.

Jose.

Let's start with the codes.

Po129 refers to barosensor

Po344 is a code for the camshaft position sensor

Po339 crankshaft position sensor

Po340 camshaft position circuit malfunction

Po335 crankshaft POS sensor malfunction

Po122 throttle pedal position

Item 2,3,4,5 relate to each other that s camshaft and crankshaft position sensors. Since both already show a malfunction code, it would be advisable to change.

Sometimes other codes show up because there is a relation but not that the item is bad.

P0335 is for a faulty crankshaft position sensor. AZone does carry the part but shows special order in my area.

P0157 - O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2)


P0335 - Crankshaft Position Sensor A Circuit Malfunction

The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 will set.

NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start.

Symptoms may include:
* Vehicle may not start (see above)
* Vehicle may run rough or misfire
* MIL illumination

Causes: A P0335 "check engine light" code could be caused by:
* Damaged CKP sensor connector
* Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway)
* Sensor output open
* Sensor output shorted to ground
* Sensor output shorted to voltage
* Failed crank sensor
* Broken timing belt
* Failed PCM

Possible Solutions:
1. Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal.
2. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there's no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn't be performed if you\'re not familiar with automobile electrical systems). Is the sensor within resistance specs?
3. If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay?
4. If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

This code is basically identical to P0385. This code P0335 refers to Crankshaft Posistion Sensor "A", whereas P0385 refers to Crankshaft Position Sensor "B". Other crank sensor codes include P0016, P0017, P0018, P0019, P0335, P0336, P0337, P0338, P0339, P0385, P0386, P0387, P0388, and P0389.



P1372 - Segment Time Incorrect

This engine is very sensitive to overheating and will easily warp the cylinder head. On the other hand, all the performance symptoms as well as the misfire code can be caused by a faulty crank sensor.

This leaves you at a crossroads as to how to diagnose. You could replace the crank sensor and see what happens. Or you could do a compression test to get an idea of the general health of the engine.

As for the lack of heat, you may have an air pocket in the cooling system or it may not be completely repaired. If, for example, the thermostat were stuck shut causing the pressure to build and crack your radiator, you'd still have the problem that you have no coolant flow, resulting in no heat.

Unfortunately, considering the overheating, my inclination is that you're more likely to need a cylinder head than any of the minor repairs I've suggested. But the only way to find out is to check the cooling system, compression, and crank sensor.


Hope helps.

Check this video out. Code P0725 P0335 P0340 Crankshaft Positioning Sensor Replacement DIY Nissan