Question about 2003 Cadillac Deville

1 Answer

How do I remove rear seat cushion to replace battery

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

Thats really simple.....take your hand and slide between the carpet and bottom edge of seat and tug upwards on one swift motion

Posted on Sep 19, 2013

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the fuses located for the air conditioner in a 2001 pontiac bonneville


The interior fuse box in a Pontiac Bonneville is underneath the backseat on the driver's side.

To remove the rear seat cushion:
1. Pull up on the front of the cushion to release the
front hooks.
2. Pull the cushion up and out toward the front of
the vehicle.

To reinstall the rear seat cushion:

1. Buckle the center passenger position safety belt, then
route the safety belts through the proper slots in the
seat cushion. Don't let the safety belts get twisted.
2. Slide the rear of the cushion up and under the
seatback so the rear - locating guides hook into the
wire loops on the back frame.
3. With the seat cushion lowered, push rearward and
then press down on the seat cushion until the spring
locks on both ends engage.
4. Check to make sure the safety belts are properly
routed and that no portion of any safety belt is
trapped under the seat. Also make sure the seat
cushion is secured.

Notice:
The battery and main fuse blocks are located
under the rear seat cushion. The battery's ground
terminal and some relay wires are exposed.
To help avoid damage to the battery and wires,
be careful when removing or reinstalling the seat
cushion. Do not remove covers from covered
parts. Do not store anything under the seat, as
objects could touch exposed wires and cause
a short.

Jul 22, 2014 | 2001 Pontiac Bonneville

2 Answers

Battery location


it is under the back seat. you need to lift out the bottom part of the back seat to get to the battery.

Oct 17, 2013 | 2002 Cadillac Deville

1 Answer

Replace battery under rear seat cushion


just grab the seat from the edge at carpet on the bottom and pull upwards in one swift motion. you've another fuse block under there as well

Jul 06, 2013 | 2003 Cadillac Deville

1 Answer

Battery location


The battery is on the passenger side under the lower seat cushion. When removing the rear cushion make sure you disconnect the wiring for the rear heated seat cushion if it is equiped with heated seats

Sep 16, 2010 | 2002 Cadillac Deville

1 Answer

How do i remove the backseat in my thunderbird?


Rear Bench
(see Figure 4)
  1. Bearing down with your knee on the rear seat cushion, push the cushion rearward and disengage it from the retaining brackets.
  2. Remove the rear seat armrests if applicable.
a32ebe2.jpg

Fig. 4: Pull the bottom of the seat upwards and pull out
  1. Remove the seatback lower retaining screws and seat belt bolts.
  2. Grasp the seatback at the bottom and lift it up to disengage the hanger wire from the retainer brackets.

To install:
  1. Position the seat back assembly so that the hanger wire is fully engaged in the package tray slots.
  2. Install the lower retaining screws and tighten to 13-19 ft. lbs. (17-37 Nm).
  3. Position the seat cushion assembly into the vehicle.
  4. Apply knee pressure to the lower portion of the seat cushion assembly. Push rearwards and down to lock the seat cushion into the seat retainer.
  5. Check the seat cushion to ensure it is secured into the floor retainer.

Rear, Fold-Down Seats
  1. Push the rear cushion rearwards, then lift to release. Remove the cushion.
  2. Remove the 2 lower retaining screws attaching the seat back to the floor.
  3. Lift up and disengage the upper clips of the seatback from the top of the folding floor.
  4. Remove the seat assembly.

To install:
  1. Position the seat back assembly and align the retaining hooks. Ensure hooks fully engage in slots.
  2. Install the two outboard retaining bolts, then tighten to 13-19 ft. lbs. (17-27 Nm).
  3. Lower the seat backs and install the upper retaining screws.
  4. Install the lower center retaining screw, tighten to 13-19 ft. lbs. (17-27 Nm).
  5. Install the rear seat cushion. Ensure the rear seat cushion front retainers latch properly.

Hope helps (remember rated this).

Jul 01, 2010 | 1994 Ford Thunderbird

3 Answers

Is there another fuse box than under the hood.


There are 2 fuse boxes, they are called Bussed Electrical Centers.
The front Bussed Electrical
Center (This is one fuse box) is located in
the front of the engine
compartment on the
passenger’s side. Lift the
cover to gain access

Rear Underseat Bussed Electrical Center (BEC)
The rear BEC is located
beneath the rear seat on the
driver’s side. The rear seat
cushion must be removed to
access the BEC. See
“Removing the Rear Seat
Cushion” in the Index.

Mar 10, 2010 | 2000 Buick LeSabre

3 Answers

Battery removal 2000 cadillac deville


Its on passenger side under rear seat cushion. Get in back seat FACING rear seatback, grab under lip of bottom seat cushion, and pull straight up. Disconnect seat heater connector (if so equipped) on passenger side and remove seat bottom. Tada! There ya go! Oh... btw. Its a $150 battery due to the venting system designed into it to vent fumes through a tube to the outside world. Thanks Cadillac!!! :(

Jul 03, 2009 | 2000 Cadillac DeVille

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

Replace rear seat belt in 1993 Toyota Corolla


OK. On the front edge of the seat bottom cushion, pull up hard, both sides. This will dislodge the 2 clamps that holds the seat cushion to the floor. Pull the seat cushion out & set it aside. You will now see the female latches bolted to the area where the rear of the seat cushion meets the rear seat back bottom. Remove the bolts (14 mm I think).

Oct 07, 2008 | 1993 Toyota Corolla

Not finding what you are looking for?
2003 Cadillac Deville Logo

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...