Door sensor how to disable door sensor

There is a fuse for the door ajar sensor and the alarm, but it may not be advisable to pull it as it could disable other functions as well. The fuse box is located under the dashboard on the driver's side. The fuse for the door ajar sensor and the alarm is usually labeled as "door" or "security."
However, pulling the fuse for the door ajar sensor and the alarm may not completely solve the problem. If the latch is not sealing properly, the sensor may still detect an open door even if the alarm is disabled. In this case, you may need to have the latch mechanism inspected and possibly replaced.
If you do decide to pull the fuse, make sure to consult your owner's manual to ensure that you are pulling the correct fuse and that it won't affect any other important systems, such as the power windows or the radio.
If you are not comfortable with DIY repairs, it may be best to bring your vehicle to a reputable mechanic or dealership to have the issue diagnosed and repaired.

To turn off the door sensor on your 2004 Toyota Sienna, you will need to follow these steps:

1. Open the door of your Sienna and locate the door sensor, which is a small black or silver button located near the top of the door frame.
2. Press and hold the door sensor button for a few seconds until the sensor's light turns off.
3. Close the door and test the sensor to make sure it is no longer active.

Note: Disabling the door sensor will prevent your Sienna from automatically locking or unlocking the doors when you open or close them.

Inflatable Restraint Side Impact Sensor Replacement
Inside drivers door ! Have to take inside door panel off . You mite find a video on youtube on how to do it .

Removal Procedure
Caution: Refer to SIR Caution in the Preface section.




Caution: Do not strike or jolt the inflatable restraint side impact sensor (SIS). Before applying power to the SIS make sure that it is securely fastened. Failure to observe the correct installation procedures could cause SIR deployment, personal injury, or unnecessary SIR system repairs.

1. Disable the SIR system. Refer to SIR Disabling and Enabling or to SIR Disabling and Enabling .
2. Place the window in the raised position to access the sensor.
3. Remove the door trim panel. Refer to Front Side Door Trim Panel Replacement in Doors.
4. Remove enough of the water deflector to access the side impact sensor (1).
5. Loosen the bolts (2) on the inflatable restraint side impact sensor (1).
6. Remove the inflatable restraint side impact sensor (1) out from the door (4).
   
   
7. 
8. Remove the connector position assurance (CPA) (3) from the side impact sensor connector (4).
9. Disconnect the side impact sensor connector (4).
10. Remove the sensor from the vehicle.

This is normal.

Its sensing that there is a key in the ignition. You have to replace the switch in the ignition cylinder that senses a key is inserted. Or alternatively access a wiring diagram and cut the wire from the key sensor to eliminate it.

donde se encuentra la llave que hace contacto con la puerta, debes desarmarla y dejar los cables unidos y encintados

I wouldn't disable the sensor but are you sure it is a seat belt sensor dinging at you and not a door sensor? They both sound the same. With all the doors closed but the key in the ignition. If the warning ding starts then your problem is a door sensor, a common issue in that model and usually related to the side door.

Not positive if it works on VW's but try locking/ unlocking the passenger door with the key. There are sensors in both doors.

Had this problem for some time. I have had the dealer replace motor etc. Problem still returns. Noticed that the foam seal around the right side door has started flatening out over time and was beginning to spill into the lipped plate that the door sensor buttons possibly could be prevented from making proper contact. Trimmed approx. 3/8 of an inch off the foam in the area of the plate, and the problem seems to have gone away. Hope this helps.

One of the doors or the boot is not closed or the sensor is faulty on one of these. You can remove the sensor and disconnect the plug to disable the sensor until you get it fixed.