Need to replace the low beam headlight on drivers side

Check the wiring on that light. Also check the bulb with a couple of wires to the battery, or swap the bulb left to right to make sure the new bulb is okay.

Dipped probably means low beam . If the bulb is good you need to check for power and ground to the bulb connection .

Here's a link on replacing your light bulb on your VW. Sparky Answers 2001 VW Beetle Changing The Low Beam Headlight Bulb HERE'S A VIDEO,ALSO How To Change Head Light Bulb VW Beetle

bad connection or bad earth check all connection or bulb

HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

try the fuses or wire fuse links , the only other thing in the circuit is the wires broken or the light low switch is bad

When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(

The low beam bulb needs to be replaced. Go to an autozone store as they will sell you the bulb, and even assist you in their parking lot with installing it.

Honda Headlight Bulb(H1) - This bulb is the high and low beam bulb for your vehicle. One bulb required for each headlight.

This headlight bulb fits:

• CR-V 2005-2006 (requires 2 bulbs per side)

You will need to change the bulb.