Need picture of alternator assembly with brackets 99 Malibu

How To Install Replace Serpentine Belt Chevy Malibu 97-03 ...

? 9:28
www.youtube.com/watch?v=KyEm7LtoI8k
Sep 23, 2011 - Uploaded by 1A Auto Parts This video is applicable to 97, 98, 99, 00, 01, 02, and 03 Chevy ...my Malibu belt broke and quoted by a friend that works at a shop said it would ...

GOT TO ANY AUTO PARTS STORE THEY SHOULD HAVE A ENGINE MOUNT.IF NOT.DEALERSHIP CAN ORDER YOU ONE.

1. Disconnect the negative battery cable.
   
2. Remove the drive belt.
   
3. If necessary, remove any splash shielding for easier access to the alternator.
   

For easiest access to the alternator assembly, first remove the splash shield mounting fasteners ...
Click to Enlarge

... then swing it out of the way for access to the alternator assembly
Click to Enlarge

View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

1. Tag and disengage the alternator wiring.
   

It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.

1. If equipped, remove the front alternator assembly mounting plate.
   

Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly
Click to Enlarge

Remove the front alternator assembly mounting plate from below the vehicle
Click to Enlarge

1. Unfasten the alternator mounting and pivot bolts and remove the alternator.
   
2. If installing the original alternator assembly, push out the pivot bushing as illustrated.
   

After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud
Click to Enlarge

Remove the two alternator bracket-to-engine mounting bolts

Remove the alternator and mounting bracket assembly from the vehicle
Click to Enlarge

If re-installing, the alternator has a pivot bushing on the pivot arm that should be pushed out before installation

Mount a C-clamp and 18mm socket on the alternator pivot bushing ...

... then compress the C-clamp until it pushes the alternator pivot bushing out

To install:

1. Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
   
2. If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
   
3. If removed, install the front mounting plate.
   
4. Engage the alternator electrical connections.
   
5. If removed, install the splash shield.
   
6. install the drive belt and attach the negative battery cable.
7. 

the job is akward ive incl as much info you need to repair yourself

plz comment reply if need more info

I have the same Jeep model 5.2L V8, to replace the alternator, check the next procedure...

Once the determination is made that the alternator is at fault, off vehicle testing can be used to determine the defective component inside the alternator.
See Figures 1 through 11

1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. If necessary, remove any splash shielding for easier access to the alternator.

Fig. 1: For easiest access to the alternator assembly, first remove the splash shield mounting fasteners ...

Fig. 2: ... then swing it out of the way for access to the alternator assembly

Fig. 3: View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

1. Tag and disengage the alternator wiring.

It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.

1. If equipped, remove the front alternator assembly mounting plate.

Fig. 4: Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly

Fig. 5: Remove the front alternator assembly mounting plate from below the vehicle

1. Unfasten the alternator mounting and pivot bolts and remove the alternator.
2. If installing the original alternator assembly, push out the pivot bushing as illustrated.

Fig. 6: After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud

Fig. 7: Remove the two alternator bracket-to-engine mounting bolts

Fig. 8: Remove the alternator and mounting bracket assembly from the vehicle

To install:

1. Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
2. If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
3. If removed, install the front mounting plate.
4. Engage the alternator electrical connections.
5. If removed, install the splash shield.
6. stall the drive belt and attach the negative battery cable.

Hope this helps (remember to rate and comment this answer).

Should be just a bracket, contact a salvage yard for info and best price. Some times even Ebay has these kind of parts...

Removal & Installation

Once the determination is made that the alternator is at fault, off vehicle testing can be used to determine the defective component inside the alternator.
See Figures 1 through 11

1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. If necessary, remove any splash shielding for easier access to the alternator.
   

Fig. 1: For easiest access to the alternator assembly, first remove the splash shield mounting fasteners ...



Fig. 2: ... then swing it out of the way for access to the alternator assembly



Fig. 3: View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

1. Tag and disengage the alternator wiring.

It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.

1. If equipped, remove the front alternator assembly mounting plate.

Fig. 4: Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly



Fig. 5: Remove the front alternator assembly mounting plate from below the vehicle

1. Unfasten the alternator mounting and pivot bolts and remove the alternator.
2. If installing the original alternator assembly, push out the pivot bushing as illustrated.
   

Fig. 6: After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud



Fig. 7: Remove the two alternator bracket-to-engine mounting bolts



Fig. 8: Remove the alternator and mounting bracket assembly from the vehicle



Fig. 9: If re-installing, the alternator has a pivot bushing on the pivot arm that should be pushed out before installation



Fig. 10: Mount a C-clamp and 18mm socket on the alternator pivot bushing ...



Fig. 11: ... then compress the C-clamp until it pushes the alternator pivot bushing out
To install:

1. Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
2. If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
3. If removed, install the front mounting plate.
4. Engage the alternator electrical connections.
5. If removed, install the splash shield.
6. Install the drive belt and attach the negative battery cable.

Also, other details can find in your Grand Cherokee Repair Manual.

Good luck (and remember rated this).

check idle, for a 3.1 it should be about, 750 rpms,

Jeep Cherokee 1984-1998
Alternator - Removal & Installing

1. Disconnect the negative battery cable.
2. Remove the drive belt.
3. If necessary, remove any splash shielding for easier access to the alternator.

Fig. 1: For easiest access to the alternator assembly, first remove the splash shield mounting fasteners...



Fig. 2: ...then swing it out of the way for access to the alternator assembly



Fig. 3: View of the alternator electrical connections-(A) battery positive, (B) field terminals, (C) wire harness hold down, (D) ground terminal

4. Tag and disengage the alternator wiring.

It may be necessary to remove the alternator and mounting bracket from the vehicle as an assembly.



5. If equipped, remove the front alternator assembly mounting plate.



Fig. 4: Remove the six nuts and bolts that secure the front mounting plate to the alternator assembly



Fig. 5: Remove the front alternator assembly mounting plate from below the vehicle

6. Unfasten the alternator mounting and pivot bolts and remove the alternator.
7. If installing the original alternator assembly, push out the pivot bushing as illustrated.



Fig. 6: After removing the alternator assembly front mounting plate, remove the front engine-to-alternator bracket mounting stud



Fig. 7: Remove the two alternator bracket-to-engine mounting bolts



Fig. 8: Remove the alternator and mounting bracket assembly from the vehicle



Fig. 9: If re-installing, the alternator has a pivot bushing on the pivot arm that should be pushed out before installation



Fig. 10: Mount a C-clamp and 18mm socket on the alternator pivot bushing...



Fig. 11: ...then compress the C-clamp until it pushes the alternator pivot bushing out


To install:

8.Mount the alternator to the brackets with the nuts and bolts. Tighten the two mounting bolts and nuts to 40 ft. lbs. (54 Nm).
9.If the alternator and mounting bracket were removed as an assembly, install the assembly into the vehicle.
10. If removed, install the front mounting plate.
11. Engage the alternator electrical connections.
12. If removed, install the splash shield.
13. Install the drive belt and attach the negative battery cable.


More details for testing and diagnostics you can revies:
- Section-8A-Electrical-95xj8a
- Section-8B-Battery-Starter-Generator-Service-95XJ8B

I hope help you whit this, good luck (remember rated this help).

This is a relatively easy task, the bulk of the work has been for you. The rear view mirror assembly simply slides onto that metal block that was glued to your windshield. Your mirror mount (the part that slides onto the metal bracket) may be cut differently or shaped different from the rest of that part. you simply need to line that up with the metal mount on your windshield. slide the mirror on and tighten down the set screw if you have one. I've listed the steps below

1. find the base mount for your mirror (this is the bottom of the mirror that sits on the windshield)

2. look for a cut out or flat part of the mirror base.

3. line the flat part of the mirror base with the metal mount bracket on the windshield.

4. slide the mirror onto the metal bracket (this may require you to wiggle while you slide the mirror onto the metal bracket).

5. tighten the set screw on the mirror base ( this is important because your mirror will vibrate off the bracket if you don't.

Note some mirrors slide from the bottom of metal mount bracket and some slide from the top. it sort of depends on the manufacturer and/or the way the bracket was installed.

Hope this helps

If this is for the 3.0L Vulcan engine, it's really easy. There are two mounting bolts and a stud nut. The mounting bolts go through the left side of the mounting bracket and through the alternator (it's at the top of the serpentine assembly). You'll have to take the stud not off from the lower intake manifold to remove the second mounting bracket. Make sure you disconnect the negative battery terminal first so that you don't fry anything. You'll also have to remove the nut that attaches the ground to the alternator and remove the wiring harness. The nut is enclosed in a black rubber pocket that protects the connection from moisture. After you've done all this, just pull it up and off the assembly. Installation is the reverse of removal.