Instructions to program 1999 Toyota keyless transmitter

You need to contact Toyota on this question.

follow this link for a step byu step guide
Camry programming instructions for TDS Rostra keyless entry remote FCC...

Great news, your 1998 Toyota Camry Key Fob is self programmable. Below are the programming instructions. Be patient, it might take you a few times to get this right. It is all about timing.

Most remotes can be self-programmed. If this procedure does not work, you must have your remote programmed by a professional automotive locksmith or dealership.


Obtain all remote transmitters for this vehicle.
1. Insert key into ignition and turn ignition switch to ON position.

2. Locate the ECU (Engine Control Unit) and press and hold the ECU PROGRAMMING button for 3 seconds. The ECU will be located under one of the front two seats, the trunk, or under the dashboard on the drivers side. You will need a small pointy object like a pen to depress the ECU button. After pressing the ECU button for three seconds, you will see the STATUS MONITOR LED turn on for 5 seconds. Vehicle is now in programming mode.

3. Press and release the top button on the remote. The STATUS MONITOR LED will turn off. A chirp will be heard as well as one flash of the exterior lights.

4. Turn off the ignition. Programming is now complete, test remotes for proper programming.

Toyota is having problems.. Nothing surprises me

See your Toyota dealer please

I believe this was done as a safety feature. It stops a potential car hyjacker from sneaking in the passenger door when you open the driver door. I know recent Hyundai models are set up such that if you turn the key in the driver's door once it only unlocks the driver's door. If you turn it twice in quick succession it unlocks all of the doors. Maybe the Camry is set up the same way.

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

• 2001 - 2004 MY Elantra
• 2001 - 2004 MY Santa Fe
• 2002 - 2004 MY Sonata
• 2001 - 2004 MY XG300/350

NOTE

• The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
• The most current Keyless Adapter Cable Instructions are available in the following shop manuals:

SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:

1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable.
2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
   
3. Turn the Hi-Scan Pro ON
   and press ENTER
   . NOTE "Release date 29. Sep. 2003" OR LATER
   must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
   
4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
   and press ENTER
   .
5. Select vehicle model and press ENTER
   .
6. Select option "TRANSMITTER CODE SAVING"
   and press ENTER
   .
7. Ensure that the key has been removed from the ignition cylinder before proceeding.
8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
   
9. Press ESC
   on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

get a used one.it can be reprogrammed with the obd2 system for 100 bucks.

Yes.

Rate this.