Wiper Blades how to remove/replace wiper blades on Mercedes Benz 2004 e320

Changing wiper blades on a CLK500 is the same as on any car. They just slide on and off and are held on with a tiny metal clip on the end. The instructions are on the side of the wiper blade box when you purchase them.

WHEN I START MY MERCEDES C- 180 MODEL 1997 YHE SRC LIGHT REMAIN ON AND THE AIR BAG LIGHT DOES NOT COME ON , HOW EVER IF I USE DIPPER OR WIPER BOTH DOES NOT WORK INSTEAD THESR LIGHT FLIERS WHEN WIPER LEVER IS PLACED ON OR THE LIGHT GOES OF TILL THE TIME DIPPER SWITCH IS PRESSED

Replace all fluids, replace belts and hoses. Check brakes for proper operation, get tires checked and replaced as needed. Replace wiper blades. Sitting unused is the worst thing for any vehicle. Check all lights for proper operation as well.

model: 2001 C240 problem: wiper blades "park" almost in the middle of a windshiled when turned off. When wiper blades are on they cover complete range of a windshiled.

the blower motor for the a/c is located under the windshield wiper motor. you access it from the engine compartment by removing all the trim covers under the windshield, also have to remove the wiper motor and assembly but be careful not to crack the windshield. once you pull all the covers out of the way you will see the blower motor housing. remove clips and voltage regulator in order to remove top cover of blower motor housing.

Check that the wiper arm hasn't come loose.
Tighten the nut under the cover.

Open your hood, look under wiper if you see dust filters you have them if not you dont. Its tough to remove the blades without breaking them i dont suggest it.

pull off the whole assembly, check out the inside of the wiper assembly, sounds like gears are wornout

How to Replace Wiper Blades Guide (Typical):
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades theactual action of replacing the blade is no big deal, it's the locationof the blade down below the hood that can make it difficult though.Sometimes it helps to open the hood to gain access to the wiper blades.Other times it is helpful if the wiper blade is somewhere in the motionline of wiper action. The trick is to get the wiper to stop somewherein the wiper arc. Turn the wipers to the on position and allow thewipers to start, and then shut the key off when the wiper has arrivedin a desirable position on the windshield. To replace your wiper bladesplease follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wiperson, when the wipers are in the middle of their arc turn the key to theoff position. (Note: if this can't be done because of wiper conditionand you want to avoid scratching the windshield please open your hoodto gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade onthe mounting pin completely allowing the wiper arm to become dislodgedand possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when theblade is not properly balanced allowing the blade to "flop" back andforth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.

How to Replace Wiper Blades Guide:
Potential tools needed to replace wiper blades:

• Flat blade screwdriver (small)
• Small nosed pliers
• Latex or vinyl gloves
• Safety goggles

To replace wiper blades the actual action of replacing the blade is no big deal, it's the location of the blade down below the hood that can make it difficult though. Sometimes it helps to open the hood to gain access to the wiper blades. Other times it is helpful if the wiper blade is somewhere in the motion line of wiper action. The trick is to get the wiper to stop somewhere in the wiper arc. Turn the wipers to the on position and allow the wipers to start, and then shut the key off when the wiper has arrived in a desirable position on the windshield. To replace your wiper blades please follow the step by step instruction below. Also, watch the How to replace wiper blades video below to gain additional information. The method in which the wiper blades are attached will vary slightly.

• Step 1: With the hood closed, turn the wipers on, when the wipers are in the middle of their arc turn the key to the off position. (Note: if this can't be done because of wiper condition and you want to avoid scratching the windshield please open your hood to gain access)
• Step 2: Locate the mounting clips at the top pivot on the wiper blade
• Step 3: Release the clip and remove the wiper arm
• Step 4: Match the size of the old blade against the new blade to ensure proper fit and operation
• Step 5: Reinstall the new wiper blade and recheck wiper operation

Common Problems:

• Make sure the wiper blades are the same size as the original blades.
• When replacing wiper blades not getting the blade on the mounting pin completely allowing the wiper arm to become dislodged and possibly causing damage to the windshield.
• Using wiper blades after the blade has failed permanently damaging the windshield by craving scratches in the wiper arc.
• Wiper blade can create a chattering noise when the blade is not properly balanced allowing the blade to "flop" back and forth as the wiper direction changes.

I hope help you with this (remember rated this help) Good luck.