Cars & Trucks Logo

Related Topics:

Anonymous
Anonymous Posted on May 01, 2013
Be the first to answer

How to remove the front bumper cover

Just trying to replace a signal bulb and I need to remove the cover.

Answer This Question

5 Related Answers

Ronnie Wilson

  • 1596 Answers
  • Posted on Jan 16, 2009

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Ad
Fleetw00d

Fleetw00d

  • 31 Answers
  • Posted on Jan 26, 2009

SOURCE: Bumper cover removal

It is a little more complicated than that. There are two nuts below the headlight assemblies in the engine compartment. You will need to remove the battery and overflow bottle to get at the one on the passenger side. Remove the turn signals in the bumper, then there are 2 or 3 bolts holding a mounting bracket behind the each of the turn signals. There are a number of bolts with washer heads and reatiners on the underside of the bumper as the previous responder indicated.

Anonymous

  • 9 Answers
  • Posted on Apr 14, 2009

SOURCE: Headlight Issue

You can replace the bulbs wihout removing anything. The passenger side is super easy. The driver side is tougher because there isn't much room to stuff your hands, but it can be done. If you must pull the battery, make sure you have your radio security code on hand because you will need it after hooking the battery back up. I'd suggest not removing the battery and just taking your time to get the driver side bulb replaced.

Anonymous

  • 6 Answers
  • Posted on Jul 03, 2009

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Anonymous

  • 2 Answers
  • Posted on Feb 12, 2010

SOURCE: Acura - change headlight bulb 2001 3.2 TL

I will be working on my CL and keep you posted on what to do.. shouldn't need to remove the bumper.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Need to replace front turn signal on srx how to proceed
What year is it ? replace front turn signal ??? You mean the bulb . You may need to remove the headlamp assemble an the bumper cover .
Read full answer
May 19, 2019 • Cadillac SRX Cars & Trucks
tip

Change the front turn signal bulb on Cadillac SRX
I have found a short cut for changing the front turn signal bulb
  1. Remove the inner fender well cover and then you can remove the light assemble from underneth and replace the bulb.
  2. The cover is attached with a bunch of push on body clips, pry the button up with a screwdriver and pull out fastner.
  3. Then there are two screws holding the light assembly on the bottom and inner side, it clips into the bumper on the outter side. From there it's pretty simple.
  4. FYI the GE replacement cross reference is wrong it's a Sylvania 3757A LL bulb.
Read full tip
on Dec 02, 2009 • Cadillac SRX Cars & Trucks
0helpful
1answer

How to Replace Headlight Bulb on 2005 Prius?
Remove fender well trim ( a few screws)
Remove front bumper COVER (not the bumper- the plastic cover)
About 14 screws. Mostly on the underside, get a creeper, and a few
on the top.

Remove the (left or right side) Headlight assembly ( a couple more screws).
One assembly contains the headlight, turn signal and running light. Unplug
the electrical connector from the assembly. All bulbs remove from the back
of the headlight assembly. Headlight is held in place by bail wire, smaller
bulbs are 1/4 turn.
Read full answer
Oct 20, 2016 • 2005 Toyota Prius
0helpful
1answer

How do you access the FRONT park/turn signal light, in the bumper below the headlight, to replace burned out bulbs?
It all depends on the vehicle. Many newer cars you have to remove the front bumper cover to get to the lights.
Read full answer
Oct 28, 2014 • Cars & Trucks
0helpful
1answer

How to change front turn signal bulb in Cadillac cts
KMTANNER is correct for the 2003-2007 CTS. For the 2008+ CTS, you need to remove the bumper. The bumper comes off fairly easy, but there are a 2 hidden screws. Look for the youtube video on removing the bumper. I have a 2004 and 2009 CTS. I did both.
Read full answer
Sep 13, 2014 • Cadillac CTS Cars & Trucks
1helpful
1answer

How to replace bulb in front bumper turn signal housing 1995 jag xj6
hello,

  • Identify the blown bulb. Note that if a headlight bulb has blown, the dip beam is on the outside and the high beam is on the inside. Turn off the ignition switch and light switches.

  • Open the hood and replace any blown headlight bulbs. Press the plastic spring clips and remove the bulb holder from the assembly. Pull the bulb out of the bulb holder and replace it with a new bulb. It only fits one way. Be sure not to touch the bulb's glass. Replace any parking lights at the same time, they are in the headlamp unit too.

    • Remove the front turn signal light unit in the bumper to change the turn signal bulb. Push gently on the inside edge and insert a blade between the bumper and the lens at the outside edge. Compress the spring and remove the lens. Fit a new lamp by inserting it into the plug. The side marker light is changed using a similar process.

    • Open the trunk to replace the rear fog light, stop light, tail light, reversing light and turn signal light. Remove the rear light cover and turn the bulb holder fastener 90 degrees counter clockwise. Remove the expired bulb, fit a new one and replace the parts, turning the bulb holder clockwise.

    • Thanks..
    Read full answer
    May 21, 2011 • 1995 Jaguar XJ6
    0helpful
    1answer

    How do I change my front turn signal? I can access the lower signal from under the bumper, I can't access the signal that is next to the headlight. There are no screws in front to take the plate off,...
    The signal light on the grill next to the head light can be accessed by removing the the front grill. Your going to need a torque screw driver to remove the grill to get to the light bulb. The signal from under the bumper can be accessed from behind the bumper and you need not to take the turn light assemble off from the bumper. There are LED light bulbs available now and last much longer then the conventional bulbs and cost not that much more. Auto Zone carries these replacement LED bulbs and they can give you the step by step instruction to getting the job done if you need more illustration. Good luck and hope this helps and please rate, keep me posted. Be glad to help you get your lights replaced.
    Read full answer
    Jan 10, 2010 • 1991 GMC Sonoma
    1helpful
    1answer

    How do you replace the turn signal bulb on the side of the front bumper?
    You will need to loosen the bumper cover clips below the bumper and inside the fender liner and possibly where they attach to the grille. By loosening about 6- 8 large Philips screws, the cover should shift enough to get in behind the cover and pull the light , change the bulb and reinstall.
    This light is accessible from inside the bumper skin.
    Read full answer
    Jan 02, 2010 • 1999 Lexus RX 300
    1helpful
    2answers

    Replace front headlight
    Headlights Removal & Installation WARNING
    Halogen bulbs contain a gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
    To help avoid personal injury:
    • Turn off the headlamp switch and allow the bulb to cool before changing bulbs. Leave the headlamp switch off until the bulb change is complete.
    • Always wear eye protection when changing a halogen bulb.
    • Handle the bulb only by its base. Avoid touching the glass.
    • Do not drop or scratch the bulb. Keep moisture away.
    • Place the used bulb in the new bulb's carton and dispose of it properly. Keep halogen bulbs out of the reach of children
    To Remove:
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • LH and RH engine under covers
      • RH and LH Front fender liners
      • Front bumper cover
    3. 2 bolts and disconnect the connectors
    4. Headlight assembly by pulling it forward
    5. To Install:
      1. Install or connect the following:
        • Headlamp assembly
        • 2 bolts and connector
        • Front bumper cover
        • LH and RH front fender liners
        • LH and RH engine under cover
    2997275.gif
    Read full answer
    Jul 25, 2009 • 1998 Toyota Camry
    0helpful
    1answer

    I have a left front clearance light out how do you get it out 1
    Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
    1. Disconnect the negative battery cable.
    2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
    3. Remove the bulb from the socket; if necessary, replace the bulb.
    4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
    5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
    Fig. 1: Common front turn signal/parking light mounting

    d16c14b.jpg
    Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

    8b774bd.jpg
    Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

    09f4811.jpg
    Read full answer
    Jul 24, 2009 • 1992 GMC Sonoma
    Not finding what you are looking for?

    View Most Popular

    Cars & Trucks

    Related Question

    Need to replace front turn signal on srx how to proceed

    • Cadillac SRX Cars & Trucks

    84 views

    Ask a Question

    Usually answered in minutes!

    Popular Questions

    Dome lights will not turn

    2008 Lincoln MKX

    Heated seats in 2007 Lincoln

    2007 Lincoln MKX AWD

    My Lincoln MKX Sunroof isn't closing completely.

    2007 Lincoln MKX AWD

    Where is the dip stick for transmission fluid on a lincoln mkx

    2007 Lincoln MKX AWD

    Power liftgate will not open with remote, instrument panel control or button in rear cargo on lincoln mkx

    2007 Lincoln MKX AWD

    Check Out the Latest Top Trucks Report!
    Check Out the Latest Top Trucks Report!

    View all Fixya Reports

    Top Lincoln Experts

    ZJ Limited
    ZJ Limited

    Level 3 Expert

    17989 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6988 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    15088 Answers

    Are you a Lincoln Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    PDF Manual
    11mkxog1e.pdf. user-manual-2011 MKX...

    2011 Lincoln MKX

    PDF Manual
    Http://www.jacobsonford.com/PDFs/2007%...

    2007 Lincoln MKX AWD

    Loading...