Engine torque settings VW lt 35 1993 2.4 turbo diesel. Code ACL

what country the books are by country (and car)
D4CB<< engine real name. 2.5L diesel series A-mark1 this year.
3.5L gas only sold in USA so zero books here or parts. zip for 2.5L
buy the manual in our secret country and tell it too so you might luck out.
none here.
sorry

1. ask maker for book there
2. or google to find sellers world wide
3. or use ebay in your country and find books to match. (not easy)

The torque settings for the big end (connecting rod) bolts on a 2008 Ford Transit 2.4L diesel engine are as follows:

• Step 1: Torque the bolts to 25 Nm (18 lb-ft) using a torque wrench.
• Step 2: Tighten the bolts an additional 90 degrees (1/4 turn) using a torque angle gauge.
• Step 3: Tighten the bolts another 90 degrees (1/4 turn) using a torque angle gauge.

Note that these torque settings are for the standard size connecting rod bolts. If your engine has oversized or undersized bolts, you will need to consult the manufacturer's specifications for the correct torque settings.
Also, it's important to use a good quality torque wrench and torque angle gauge to ensure that the bolts are tightened to the correct specifications. Over-tightening or under-tightening the bolts can lead to engine damage or failure.

Once you get the words in the right order to form the search query, you need to add the word of the part you want the torque setting for. The problem is the all the weighting is given to the torque that the engine produces and is normally right next to the horsepower

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+Torque+Settings

So insert 'wheel nuts', 'cylinder head' etc HERE

2017 Nissan Navara, 2.3 turbo diesel, HERE Torque Settings

Example for 'cylinder head'......

https://www.google.com/search?q=2017+Nissan+Navara%2C+2.3+turbo+diesel%2C+cylinder+head+Torque+Settings

..

all cars it is 1 of 3 places off the crank shaft
front ,center or rear,. some even are no the tranny flex plate.(crude reluctor)
the water beetle,
no country told. usa CAR IF YES WHY NOT SAY SO , WE USE JUST ONE 2.0l
NO ENGINE TOLD LOTS OF 2.0.
A5 BEETLE 2012-2013 TSI 2.0L??????

2013 VW beetle 2.0 TSI turbo engine. 16 VALVE?
THE EA888????? 3 generations of TSI MADE, GEN 2 IS 2008
197 bhp 2.0-litre turbo petrol engine
A5 BEETLE
VW OUCH
CALLS IT AND ENGINE SPEED SENSOR. SURE BUT IS NEVER IT'S PRIMARY GOAL EVER (rpm) THE GOAL IS EXACT SPARK AND INJECTION TIMING
NOT SPEED,
USA SHOP MANUAL SAYS.
Engine Speed Sensor G28 <<< BINGO REAL NAME FOUND, HARD TO DO.2.0l

1. On the front lower left side of the cylinder block, next to the oil separator. Refer to (see more...)
2. Removing and installing. Refer to Engine Speed Sensor G28, Removing and Installing.

PULL ENGINE COVER
Open the air guide pipe hose clamp 2
Disconnect the connector arrow.?Remove the noise insulation. Refer to see Noise Insulation; Overview - Noise Insulation.
?Remove the bolts 1 and 4 and remove the air guide hose downward from the Throttle Valve Control Module J338.
?Remove the air guide hose 1 from the charge air cooler and remove the air guide pipe downward.
Disconnect the connector 1 from the Engine Speed Sensor G28.?Remove the Engine Speed Sensor G28 bolt.

G28 IS SUPER SECRET CODE FOR CKP. (USA NAMES)

not sure what engine this is but if its a diesel cargo or serena with a cast iron head no turbo then around 80lbs ,if a smaller petrol engine with a alloy head then about 60lbs ,personally i never use a torque wrench i do it by experiance and feel ,like feeling for the bolt stretch if this sounds right but ?? you have to do plenty of them to know

The torque settings for the cylinder head on a 2003 Ford Ranger 2.5 turbo diesel WLT engine are as follows:

• Main cap bolts: 70 Nm (52 ft-lbs)
• Head bolts: 65 Nm (48 ft-lbs)
• Rocker arm shaft nuts: 25 Nm (18 ft-lbs)

It is important to note that these torque values are for the cylinder head bolts and main cap bolts only. Other fasteners on the engine, such as the oil pan bolts, may have different torque requirements.
It is also important to use a torque wrench and follow the proper tightening sequence when installing the cylinder head. Consult the service manual for your vehicle or a repair manual for the specific tightening sequence and additional torque specifications.
I hope this information is helpful. If you have any further questions or need additional assistance, don't hesitate to ask.

17- 20 lb-ft torque would be fine.

On the flywheel is your TDC. on the deisel pump pully is your injection timing,

you will need a manual for this as diesel torque settings are different to that of a petrol engine.