Resetting the check engine light

Take it back to the oil change place. Or check the oil. If a seal is leaking or oil filter was not tightened or put on correctly oil may have leaked out and you will blow your engine!

Is is there any oil leaking in garage or driveway or where you park?

check your timing belt firts.

All it means is 5000 miles have passed since the oil change reminder was reset. You can reset it your self. Look in the Camry Hyrbid Owners Manual on Page 148 for the Resetting the engine oil maintenance data procedure. Make sure you have the A trip odometer showing when you follow along.

that code is not a code for a toyota camry, please check the code again. for futher help please call 419 689 1114

No it is not possible. The manufacturer has engineered the vehicle so I suppose they know when the maintainence should be performed. Do you need assistance with resetting the oil=life monitor?

That is for oil changes. It come on when the oil change is due.
When you have your oil change done, the lube tech should reset the this light every time.
If you need help resetting the light, let me know.

Complain to Toyota, they are fixing some of these car for free. Here is the explanation and the list of problem vehicles.

Oil sludge or black sludge is a solid or gel in motor oil caused by the oil gelling or solidifying, usually at temperatures lower than 100 degrees Celsius. Sludge can be a major contributor to Internal combustion engine problems, and can require the engine to be replaced, if the damage is severe. Sludge is usually caused by the presence of water in the oil, and can accumulate with use. Ways to minimize sludge production and accumulation includes performing frequent oil changes, using synthetic oil, and following the manufacturer's engine maintenance routine.
The following engines were reported by the Center for Auto Safety and/or their manufacturers to have a problem with sludge accumulation:

1996-2001 Toyota 3.0 L 1MZ V6

• August 1996-July 2001 Toyota Camry
• June 1998-May 2001 Toyota Camry Solara
• July 1997-May 2001 Toyota Sienna
• July 1996-May 2001 Toyota Avalon
• November 2000-July 2001 Toyota Highlander
• August 1998-July 2001 Lexus ES300
• January 1998-July 2001 Lexus RX300

1996-2001 Toyota 5SFE I4

• August 1996-July 2001 Toyota Camry
• June 1998-May 2001 Toyota Camry Solara
• August 1996-April 1999 Toyota Celica

This is the reset proceedure for a 2008 Highlander with a key-type ignition:

Turn the key ON, do not start the engine.

Look at the odometer, and verify that it displays "TRIP A". If it is on "ODO" or "Trip B", press the black stick next to the odometer to read "TRIP A".

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it IN.
DO not release it.

Turn the key ON, do not start the engine

Observe the Odometer display. You will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, whatever number that was displayed on "TRIP A" will be re-displayed..

Now release the black trip meter reset stick.

This completes the reset procedure, and it will be back on in 5,000 miles, to remind you of you next oil change.

1.check your water pump

2.check if the engine oil light is offing in time or not,it is like the engiine oil is not being lifted in time by the oil pump,

3. what should do if is number 1 u have change the water pump and if it is number 2 then change the oil fillter drain the engine oil and replace with new one but this time around add oil treatment oil to the engine oil u change if it is sea 40

It's basically a type of oil change life/ idiot lamp that will come on briefly after 4K just after startup and then stay on steady after 5K reached after reset procedure done after each oil change.
The explanation of it's purpose and the reset procedure should be covered in your owner's manual.
I remember resetting some Toyota maint req lamp by holding in the trip reset button ,turning on the ignition key ,the mileage indicator appears as a row of flashing segments that gradually disappear and your done.
If that doesn't work ,try releasing the trip switch momentarily,just after turning the key to run position and then redepress and hold the trip reset button in (before the cluster completes it's lamp prove out)