Question about Jeep Liberty

1 Answer

CHANGED HEADLIGHT ASSEMBLY ON 2002 JEEP LIBERTY ONLY HIGH BEAM LIGHT COME ON

REPLACED HEADLIGHT ASSEMBLY ON DRIVERS SIDE AFTER PUTTING EVERYTHING BACK ONLY HIGH BEAM LIGHT COMES ON.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 47 Answers

Try flicking the mulit-function switch high beam on and off. There has been known problems with this switch, but mostly the first place to start is with some new light bulbs.
Or possibly your low beam filaments are burnt out. You have to replace the bulbs. Each bulb has a lowbeam and a high beam filament.

Posted on Jun 01, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Robert Debison

  • 412 Answers

SOURCE: 2003 dodge ram deisel change fcm no change.still

sounds like fuseblock underhood is faulty..front control module is on fuseblock

Posted on May 22, 2009

Anonymous

  • 12 Answers

SOURCE: high beam headlight does not work properly

it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!

Posted on Jul 13, 2009

super_guy

  • 1986 Answers

SOURCE: 2002 nissan xterra headlight is aiming up too high

on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Posted on Sep 14, 2009

alicantecoli

Colin Stickland

  • 22485 Answers

SOURCE: 2004 BMW X3 driver side low beam headlight

remove the air filter housing ,simple .this programme has a spell check thingy working and its driving me nuts ,it cant identify plain english ,write colour and it squiggles it out but color is ok .

Posted on Oct 30, 2009

Anonymous

  • 4 Answers

SOURCE: One high beam works one doesn't, gauge cluster does not light up

most honda have a light module under driver side dash panel and this module is often shortcut or burned by the inside (brown connecter)

Posted on Dec 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

2 Answers

Head light have low but when using high does not work just on one side drivers side


HELP! headlight not working even after change - Nissan Forums ...

www.nissanclub.com/...nissan.../302674-help-headlight-not-working-eve...

Apr 1, 2010 - 13 posts - ‎6 authors
My passenger side low beam headlight recently went off on me. ... I've changed the bulb again, and changed the fuse just in case, but .... My driver side headlight wire got loose so when i hit a bump at night if would flicker. ... When you notice one side not working (Low or High beam) it could be the module. Headlight replacement
15 posts
Jan 22, 2009
Low beams don't work but High's do
8 posts
Mar 20, 2005
More results from www.nissanclub.com

Dec 20, 2015 | 2004 Nissan Sentra

3 Answers

I have a 2007 Chrysler sebring and drivers low beams will not work.


try the fuses or wire fuse links , the only other thing in the circuit is the wires broken or the light low switch is bad

Nov 08, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

Subaru headlight relay


Headlights are a seperate circuit from everything else

Feb 27, 2014 | Cars & Trucks

1 Answer

2002 jeep liberty, high beem not working High beem will not stay on, you can hold the switch up and they work, let go of it and they go out. Just replaced headlight switch and still does the same thing.


when you use the headlight dimmer switch do you hear it click if you don`t then you may have to adjust the switch so it clicks and engages the switch from low to high.

Oct 14, 2011 | 2002 Jeep Liberty

1 Answer

Hi, I have a 2002 Buick Rendezvous and the high beam light will not come on on the Passenger's side headlight. The low beam works great and the high and low beams work great on the driver's side. We have...


Make sure the high beam realay under the hood fuse box is working. You can swap the hi beam relay with the horn relay to test. The hi beam filiament in the bulb can be open too.

Mar 24, 2017 | 2002 Buick Rendezvous

1 Answer

The drivers side headlight on my 2002 Saab won't


This is probably a problem with the orange headlight relay under the hood in the relay black box. Take the relay out and clean contacts and put back in. If does not fix, try a new relay or swap with another 9-5 to troubleshoot.

May 25, 2010 | 2002 Saab 9-5

1 Answer

Changing headlight, low beam, drivers side, 2002 Malibu


underhood at light there are two plastic slide pins on top of assembly. pull up on the pins to release assembly. then pull assembly from car, now you can replace the bulb. when putting back on, push in on assembly and push the pins down to hold it in.

Jan 08, 2010 | 2003 Chevrolet Malibu

1 Answer

How do i replace a low beam head light on a 94' camry ?


Things You'll Need:
  • #H11-55W and #9005 replacement bulbs (low- and high-beam bulbs for 2007 and later models)
  • #9006 and #9005 replacement bulbs (low- and high-beam bulbs for 2002-2006 models).
STEPS TO REPLACE HEAD LIGHT: Shut off the Camry's engine and set the parking brake for added safety. Also, make sure its headlights are switched off. Open the hood using the primary and auxiliary hood release latches. Locate the back of the headlight assembly and determine whether the low- or high-beam bulb needs to be replaced. Turn the headlight bulb socket counterclockwise to remove it from the assembly. Unplug the electrical connector from the back of the bulb. Carefully dispose of the bulb to prevent it from shattering or cracking.

Dec 05, 2009 | 1994 Toyota Camry

2 Answers

Changing brake bulbs


Open the back gate of the jeep. There chould be 2 screws that hold in the light assembly. Remove the screws and pull out the assembly. Replace the bulbs and replave the housing.

Jul 20, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...