My hornet car alarm model 474t does not arm automatically. You can remote start and remotely can lock doors.

To arm content theft alarm.
1. Open the door.
2. Lock the door with the power door lock switch or
the remote keyless entry transmitter. The
SECURITY light should flash.
3. Close all doors. The SECURITY light should go off
after approximately 30 seconds. The alarm is not
armed until the SECURITY light goes off.

If a locked door is opened without the key or the remote keyless entry transmitter, the alarm will go off. The headlamps and parking lamps will flash for two minutes, and the horn will sound for 30 seconds, then will turn off to save the battery power.

If you have 2 remotes does it do the same thing with both of them?
I/We have a Honda FRV and if you set the alarm from outside the car ....which locks the doors ...and the doors are opened from the inside, (yes I have set the alarm whilst still in the car,) this unlocks the doors as the drivers door has the master central locking switch on it. If I close the door withing a few seconds the alarm reactivates itself and the doors relock automatically
Presumably when your doors unlock the alarm is disarmed? Maybe your issue is linked to the receiver in the security system?

There is a difference, presumably, between you locking the doors from the dash as opposed to doing it from the remote control, the security system is not armed in the former, only the doors are locked +



GOOD LUCK

LOOK UP ON LINE TYPE IN MAKE MODLE AND YEAR OF CAR SEE IF YOU CAN FIND A MANUAL. OR GO TO SOME PLACE LIKE AUTO ZONE THEY MAY BE ABLE TO HELP.

get pro back to sort it

i have a 2002 vw cabrio and won't start after i took out the battery everbody is telling me that anti-theft is lock mode how do i rest it so i can start my car

Starting System
The function of the starting system is to crank the engine at a speed fast enough to allow the engine to start. Heavy cables, connectors and switches are used in the system because of the large currents required.
The starting system consists of a gear reduced starter motor, battery, remote control switch (ignition switch) and relay.
Vehicles equipped with automatic transaxle have a transmission range sensor attached to the circuit which prevents operation of the starter motor unless NEUTRAL or PARK are selected.
Vehicles equipped with a manual transaxle have a start inhibit switch in the starter control circuit, which prevents operation of the starter motor unless the clutch pedal is in the applied position.
------------------------------------------------------------------------------
The anti - theft protection system provides protection from unauthorized entry into the passenger compartment.
The system is controlled by an anti - theft alarm control. When armed, unauthorized entry into the vehicle is detected by lamp switches.
Once triggered, the system flashes the headlamps, the parking lamps, the alarm indicator, and sounds the horn. In addition, the starter circuit is disabled to prevent starting the vehicle until the system is disarmed.
System Arming
The system will be armed by the remote entry transmitter when the following input sequence is followed:

1. Turn the ignition switch off and remove the key.

1. Close all doors (unlocked).

1. Press the LOCK button on a transmitter to lock doors. Alarm warning lamp will turn on.

1. Wait for the anti - theft warning lamp to turn off.

The system will also be armed when the following input sequence is followed:

1. Turn the ignition switch off and remove the key.

1. Open a door. Alarm warning lamp will flash.

1. Lock doors with power door switches. Alarm warning lamp will now glow steadily.

1. Close all doors.

1. Wait for the anti - theft warning lamp to turn off.

Opening any door will activate the alarm after the alarm is armed.
Disarming an Untriggered System
The system can be disarmed by performing one of the following procedures.

• Driver or RH front door is unlocked with a key.
• Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.
• If remaining in the vehicle, turn the ignition switch to ON or ACC position.

System Triggering
The armed alarm system will be triggered if any door is opened without using a key or a remote entry transmitter to unlock the door first.
Disarming a Triggered System
Carry out either of the following steps will disarm the triggered alarm system.

• Driver or RH front door is unlocked with a key.
• Driver door is unlocked by pressing the UNLOCK button of a remote entry transmitter.

Two minutes and 45 seconds after the system has been triggered, the horns and exterior lamps will shut off automatically. The system will then reset to an armed state and will trigger again if another intrusion occurs.
--------------------------------------------------------------------
Passive Anti-Theft System (PATS)
The Passive Anti-Theft System (PATS), known as SecuriLock, is fully passive in operation and requires no special procedures by the driver to arm or disarm the system. It is invisible to normal scrutiny and is operated by a transponder within the key body. This communicates with the module through a transceiver mounted around the ignition switch lock barrel.
The PATS functionality is incorporated within the powertrain control module.
PATS keys contain an electronic device inside, and are physically larger than a non-PATS key.
The transponder code reading is carried out when the key is inserted into the ignition lock barrel, and turned from position 0' to position II' or III' to crank the engine. If the PCM receives the correct code signal, the engine will start. Should the code received not be recognized, the engine will not crank as the PATS is still armed and the engine immobilized.
Anti-Theft Indicator
Whenever the ignition is switched on the anti-theft indicator will remain on for three seconds while the system carries out an initial ignition key-read.
The anti-theft indicator will flash rapidly for three seconds to indicate the PATS has immobilized the vehicle.
For additional information on the PATS fault codes, refer to the Diagnosis and Testing section.

Check the batteries in your remote the may need replaced and if working OK check to see if you power locks work pushing the door switch. (If batteries are low they may not disengage both the alarm and the locks)

If your car has an alarm with a separate remote, it is a separate system and it is probably self-arming. When you lock the doors with the key central lock, the alarm gets armed by the RAV4 being OFF and the door locking action. When you unlock the doors with the key, the alarm is still armed because the key is not comunicating with the alarm just the cars factory keyless system.

Section 13-11: Anti-Theft System, Active 1998 Windstar Workshop Manual DESCRIPTION AND OPERATION Anti-Theft Alarm System NOTE: The system immediately monitors the ignition key lock cylinder upon removal of the key from the ignition. It is not necessary to arm the system for ignition key lock monitoring.

The anti-theft alarm system:

• protects the vehicle from unauthorized entry into the passenger compartment, engine compartment and cargo area.
• monitors the status of the ignition key lock cylinder.
• is controlled by a remote anti-theft personality (RAP) module. The remote anti-theft personality module also controls the electronic door lock functions. Refer to Section 01-14B for more details.
• when armed, detects unauthorized entry into the passenger compartment by using an input from the GEM module regarding the state of the door or liftgate (open or closed).
• protects the engine compartment with a hood switch which is located on the LH cowl vent panel and is part of windshield wiper motor wiring (17A477) .
• triggers an alarm if the ignition lock cylinder is forcibly removed from the steering column.

Once triggered, the system responds by:

• flashing the low beam headlamps, the parklamps, rear lamps and the alarm indicator warning light emitting diode (LED).
• sounding the horn (13832).
• disabling the starter circuit until the system is disarmed.

---------------------------------------------------------------------------------------------
Remote Anti-Theft Personality Module

• The remote anti-theft personality module is located behind the instrument panel (04320).
• It contains a radio receiver that receives the RF signal from the keyless entry remote transmitter (15K601) through the alarm and lock system antenna (15603) and sends the appropriate command to the power door locks, the horn relay, or the generic electronic module.
• The remote anti-theft personality module is equipped with an internal backup power supply which holds the programmed code in memory in the event the vehicle battery is disconnected.

-------------------------------------------------------------------------------
Remote Anti-Theft Personality Module Removal

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove radio. Refer to Section 15-01 .
   

1. Remove lower instrument panel center finish panel. Refer to Section 01-12 .
   

1. Lower glove box.
   

1. Remove two remote anti-theft personality module bracket retaining screws.
   

1. Disconnect electrical connectors and alarm and lock system antenna (15603).
   

1. Remove remote anti-theft personality module and bracket.
   

1. Remove remote anti-theft personality module from mounting bracket.
   

Installation

1. To install, follow removal procedure in reverse order.
   

1. Tighten remote anti-theft personality module bracket retaining screws to 6-8 Nm (54-70 lb-in).
   
   

Components The system is composed of the following components:

• remote anti-theft personality (RAP) module with integral antenna
• alarm indicator LED
• door lock cylinder switch RH, door lock cylinder switch LH
• liftgate door lock cylinder switch (220A40)
• hood switch (part of windshield wiper motor wiring (17A477))
• ignition lock anti-theft switch (19A438)

The following vehicle components are also used by the anti-theft alarm system:

• generic electronic module
• power door lock switch (14028)
• door open warning lamp switch (14018)
• autolamp relay (14N089)
• horn relay and bracket (13853) and horn (13832)
• low beam headlamps
• rear lamps (13404) and parking lamps (13200)
• starter relay
• door lock relays
• keyless entry remote transmitter (15K601)

--------------------------------
Disarming an Untriggered System NOTE: A perimeter alarm will "shut off" after 165 seconds, but the system is still triggered and is not disarmed.

An armed but untriggered perimeter anti-theft system can be disarmed by one of the following four events:

1. Unlock the doors by pressing the keyless entry remote transmitter (15K601) UNLOCK button once.
2. Unlock any door with a key.
3. Turn ignition switch to RUN or ACC.
4. The remote entry PANIC button will disarm the anti-theft system only when the perimeter alarm is triggered and sounding.

------------------------------------------------
System Triggering NOTE: Although the remote entry PANIC alarm is not associated with the monitoring of the vehicle, the user will frequently say that the theft system was triggered when actually the keyless entry remote transmitter PANIC button was inadvertently pressed. A panic alarm will not flash the THEFT indicator.

The alarm can be triggered by the following events if the system has been armed and has not been disarmed first:

• Open any door or liftgate.
• Open the hood (16612) (if the hood was open when the system was armed, it must be closed before it can trigger the alarm).
• Dislodge the ignition key lock cylinder.
• The anti-theft system may be triggered inadvertently when the module is disconnected and then reconnected. To avoid inadvertent alarm triggering, disconnect the smaller 22-way connector first.

When the system is triggered the perimeter alarm will operate as follows: The remote anti-theft personality module will pulse the following outputs at approximately 1.3 Hz, 50 percent duty cycle for two minutes 45 seconds for North America. NOTE: Other perimeter alarms can be programmed for the system.

• low beam headlamps
• parking lamps
• horn
• THEFT indicator

The perimeter alarm can be retriggered, after a perimeter alarm has sounded for 165 seconds. After a perimeter alarm has timed out, if any trigger input is first seen as normal and is then seen in its trigger state, the perimeter alarm will be retriggered. The perimeter alarm can be triggered a total of three times between an arming sequence and a disarm event. An active panic alarm will be deactivated when a perimeter alarm is triggered (a perimeter alarm overrides a panic alarm).