Question about 2004 Nissan Quest

1 Answer

Nissan Quest tail lights not working, but brake lights work..

Just the driver side tail light does'nt come on.. brake lights work and blinker works.. But when I use the blinker on the driver side and apply brakes, it blinks really fast and dims the blinker when brakes applied..

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 2,517 Answers

Start by replacing the light bulb.

Posted on Mar 18, 2013

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Coss

  • 1056 Answers

SOURCE: Brake lights not working when you apply brakes

check the brake light switch.
It's usually up under the dash, and it activated by the brake pedal.

There are 2 wires going to it. To test it, jumper across the leads.
or, watch the "action" sometimes you just need to reposition the switch to get it to work.

Posted on Aug 07, 2008

starrface

  • 2309 Answers

SOURCE: 1999 Nissan Quest. Driver side brake lock up. The

possible brake hose collapsing , interrior deterioration

Posted on Aug 06, 2010

ftw1952

frank thomas wilson

  • 10319 Answers

SOURCE: Both main brake lights are out, third brake light works.

Replace the brake light switch located by the brake pedal. That will resolve your problem

Posted on Apr 09, 2010

alpha4

Dale Ellenberg

  • 42 Answers

SOURCE: Shake in steering wheel

I believe you need your disk brake rotors turned to be true again or have them replaced. Whe you use your brakes a lot and kit puddles of cold water then it will warp the rotors which will cause the violent shaking. You may not feel it in the brake pedal even if it is warped rotors. If you don't think you have warped rotors then you should be very careful driving it because it will probably be in the steering sector arm or the idler arm on the steering shaft.
Dale

Posted on Jan 04, 2009

Anonymous

  • 2 Answers

SOURCE: 2000 Nissan Maxima. Headlights work but tail lights won't.

your dimmer switch is the proublem it is loose or just worn they wear even if you dont ever use the switch a common nissian proublem iv had the same issue

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blinker/Tail Light Issue


The Bulbs Have 2 filliments in them if 1 is burnt out that would give you the fast not working tail light there may be an issue with the brake light switch located above the brake pedal on the arm.

May 16, 2013 | 1997 Plymouth Voyager

1 Answer

Dodge dakota tail light parking light is out on driver side


those lamps have 2 filaments and one of them (the lower brightness one) is burnt out and the brighter one (brakes and blinker) still works. you need to replace that lamp

Mar 05, 2013 | Dodge Dakota Cars & Trucks

1 Answer

1996 chevrolet 1500 brake light and blinkers dont work


a bad turn signal switch the brake lights go threw the turn signal switch

Aug 26, 2012 | 1996 Chevrolet C1500

1 Answer

98 Chevy Tahoe, drivers side rear tail light assembly wont work, brake / turn signal. Replaced entire assembly, it worked for about 3 days then stopped working again. I need to get this fixed before I get...


I've got the same problem on 98 GMC Sierra.

I'm an electrical engineer, I checked the electrical diagrams and verified that there is no problem in the rear lamp assembly or wiring. With the light assembly unplugged, I can actually watch the blinker and brake signals operate with a voltmeter. The Tail light works OK.

It simply won't provide enough current to light the bulbs.

I'm afraid that it's melted one of a pair of normally closed contacts inside the blinker switch that feed the brake and turn separately on each side.

Sep 04, 2011 | 1998 Chevrolet Tahoe

1 Answer

My brake lights are not working. the bulbs are good. the tail lights, blinkers, & hazzards all work. Any suggestions???


It could be the brake light switch above the brake pedal. Maybe this switch is bad. Just another thing you might want to check.

Jun 23, 2009 | 1999 Nissan Quest

1 Answer

99 mercury mystide had rear running light broken


If the driver's side tail light is working, it's not a fuse. Use a test light to check for power at the bulb holder. One terminal will be for tail light, the other for brake/turn light. If the is constant power for tail light, replace bulb. If no power, trace wiring from bulb holder to driver's side junction. Probable broken wire between the two tail lights.

Jan 16, 2009 | 1999 Mercury Mystique

2 Answers

Tail lights wont work


sounds like ground problem- remove tail lights and look for wires going to body -remove screww clean grounding area and replace- both sides. You did not say whether the lights work when car is off? With car off and brake pedal pushed is there any brake lights ? If not procede with above.

Nov 07, 2008 | 2003 Chevrolet Cavalier

1 Answer

Brake light/ blinker


Its one of your Relay switches.

Jul 04, 2008 | 2005 Ford Focus

Not finding what you are looking for?
2004 Nissan Quest Logo

792 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...