Fog Lamp Bulb Replacement, 05 Tucson

Front Fog Light Assembly

REMOVAL

1. Disconnect the ground cable from battery.

1. Remove the two clips and lower mudguard on side that bulb is being changed.
2. Disconnect the harness connector from bulb on back of fog lamp.

Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

1. Remove the back cover.

1. Remove the spring retainer, and then detach the fog light bulb.
2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.
   

undo the hatch back {life the tail up as if you were wanting to gain access to the boot ..you will notice on either side both lighting clusters .depending on what side needs replacing .all you have to do it use a size 2 Philips screw driver to remove the black screws holding in the lighting clusters the locate the broken lamp{bulb} then twist the holder half a turn then replace the lamp {bulb} and then refit the cluster ..PLEASE note when you remove the screws you will have to gently ease the lighting cluster away from the body of the vehicle as if you try to rip it of you will damage it .there are two lugs that slide in to the bodywork of the car .make sure that you take a little time to locate them and check that the lighting cluster fits nicely to the vehicle before you replace the screws ..its worth trying the replacement lamp/bulb before you replace the screws ..just in case you have replaced a fault one with a faulty one !!! it can happen .

If your fog lamp is connected to or behind a grille, pop it out. This can be done by first removing the clips or screws connecting it to the car and gently pulling it out. (If your fog lights are not connected to a grille, proceed to step 2.)Find the bolts that hold the fog lamp in place; you may have to get underneath the automobile to do so.Using your ratchet wrench, remove the bolts.4Grab the connector on the back of the fog lamp, turn it counter-clockwise and pull it out. This should remove the actual light bulb from the lamp fixture.Remove the fog lamp from the car and place the new one in.6Place the light bulb into the new fog light and turn clockwise to lock into place.Bolt the fog lamp back into place, if you had to remove the grille, put it back now and screw/clip it back into place.Turn on the fog lights and make sure everything is working properly

p, li { white-space: pre-wrap; }

Open the hood and remove the electrical plug from the back of the fog light ballast below the headlight assembly.

Turn the fog lamp counterclockwise to unlock it from the fog light housing.

Insert the new fog lamp. Align the notches on the fog lamp housing with the tabs on the new bulb and turn the bulb clockwise to lock it into the housing.

Reconnect the fog lamp electrical plug.

you can change the bulb only -- Click to open expanded view ACDelco ACDelco 9045 GM Original Equipment Front Fog Light Bulb this is the replacement bulb Fog Light Replacement 2004 2012 Chevrolet Colorado 2007 Chevrolet Colorado... video shows how to replace

Notes FOG LAMP BULB REPLACEMENT - FRONT

REMOVAL PROCEDURE

1. Remove the front bumper fascia deflector.
2. Disconnect the electrical connector from the front fog lamp bulb/socket. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Rotate the front fog lamp bulb/socket counterclockwise to release.
2. Remove the fog lamp bulb/socket from the front fog lamp assembly.

1. Install the fog lamp bulb/socket to the fog lamp rotating clockwise until fully seated. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.

1. Connect the electrical connector to the front fog lamp bulb/socket.
2. Install the front bumper fascia deflector.

Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


Remove or disconnect the following:

Front turn signal lamp

Connector

2 screws

2 claw fittings

Fog lamp assembly

Fog lamp bulb as shown

Fog light unit

To Install

1. Install or connect the following:
   • Fog light unit
   • Fog lamp bulb as shown
   • Fog lamp assembly latch the 2 claw fittings and 2 screws
   • Connector
   • Front turn signal lamp

Trying to post the pics now....

there are a couple of screws in the front of the fog light that will remove the lense so you can replace the bulb.

have you checked to make sure it's not just the bulb ? if it is there are likely two screws holding the lens on .... or you have to lay on your back and reach behind the light and see if you can remove the bulb that way....

Robert