Wire diagram for 1992 colt vista a wire in the center council fried need to determin what fried

Mike Butler

• 6674 Answers
• Posted on Sep 08, 2009

SOURCE: Where is the ignition module for the 1992 Plymouth Colt Vista?

1.5L should be rear of engine mounted ON distributor. 2.0L should be mounted IN distributor.

Duane Wong

• 6826 Answers
• Posted on Oct 11, 2010

SOURCE: just wondering if you have a breakdown diagram for

I do not have a breakdown diagram for a distributor, but just the firing orders and description of ignition system for the Dodge Colt and related models (based on Chilton manuals) if that's what you're looking for: FIRING ORDERS Fig. 1: 1990 1.8L SOHC Engines Firing order: 1-3-4-2 Rotation: clockwise

Fig. 2: 1.6L DOHC Engine Firing order: 1-3-4-2 Distributorless Ignition

Fig. 3: 2.0L Engine Firing order: 1-3-4-2 Rotation: clockwise

Fig. 4: 1.5L Engine Firing order: 1-3-4-2 Rotation: counterclockwise

Fig. 5: 1993 1.8L Engine Firing order: 1-3-4-2 Rotation: counterclockwise

Fig. 6: 2.4L Engine Firing order: 1-3-4-2 Rotation: clockwise

To avoid confusion, replace spark plug wires one at a time. --- Distributor REMOVAL & INSTALLATION Although the distributor can be removed from the engine no matter which cylinder is about to fire, it is a good idea to have number one cylinder at TDC before distributor removal. 1.5L, 1.8L, 2.4L SOHC Engines

1. Disconnect the negative battery cable.
2. Disconnect and tag the spark plug wires from the distributor cap.
3. Disconnect the distributor harness connector.
   Fig. 1: Ignition system for the 2.0L engine
   
   Fig. 2: Ignition system for the 1.5L engine
   
   Fig. 3: Ignition system for the 1992-93 1.8L engine
   
   Fig. 4: Ignition system for the 2.4L engine
   
   
4. Loosen the distributor retaining bolt and remove the distributor from the engine. To install:
   
5. Rotate the engine until No. 1 cylinder is at TDC on its compression stroke. NOTE: Be careful not to turn it to the No. 4 cylinder TDC on its compression stroke by mistake.
   
6. Align the distributor housing and gear mating marks.
   Fig. 5: Ignition system for the 1990 1.8L engine
   
   Fig. 6: Distributor installation for the 1990 1.8L engine
   
   Fig. 7: Distributor installation for the 1992-93 1.8L engine
   
   
7. Install the distributor into the engine, while aligning the fine cut (groove or projection) on the distributor flange with the center of the distributor mounting stud.
8. Install and tighten the distributor retaining bolt.
9. Reconnect the distributor harness connector.
   Fig. 8: Distributor installation for the 2.4L engine
   
   Fig. 9: Distributor installation for the 1.5L engine
   
   Fig. 10: Distributor installation for the 2.0L engine
   
   
10. Install the distributor cap and spark plug wires.
11. Reconnect the negative battery cable.

SOURCE: wiring diagram for a toyota hilux 92 ln106 ute

my brake lights are not working. i have tested the brake switch and no power- also done a cont test between brake switch wire at the lamp and the switch and open circuit. the brake is befor the switch..-- does it go to a relay befor the fuse??

Marvin

• 85242 Answers
• Posted on Oct 16, 2012

SOURCE: mitsubishi colt rodeo wiring diagram

You can find it here

SOURCE: need alternator belt diagram for 1993 plymouth

The alternator belt drives the water pump and power steerin on these cars. You can start th engine but the steering will be very stiff and the engine will overheat within a few minutes.