Removal of console cup holder - 1994 Ford Crown Victoria

Question edited for clarity.
Question moved to model category.

2006-2007 Sonata Center Console Removal - Hyundai Forums

https://www.thehyundaiforums.com > threads > 2006-2...
Sep 19, 2006 · 3 posts · 2 authors
Any one know how to remove the center console in a 06-07 Sonata? I am trying to get to the wiring behind the 12V accessory plug.
Center console ' Hyundai Forums
2 posts
Aug 28, 2017
Hyundai Sonata '06 Center Console Cup Holder Cover
2 posts
Oct 20, 2019
Coffee in my 2006 Sonata under shift handle/gear box ...
1 post
Dec 10, 2016
center console on 2004 sonata ' Hyundai Forums
1 post
Feb 24, 2017
More results from www.thehyundaiforums.com

their is no round knob on center console --coin shelf-2 cup holders-shifter -cup holder- armrest --vents--rear audio control--12v acc--2 cup holders

To remove the cup holder/ashtray in a 2004 Mazda MPV, you can follow these steps:

1. Open the cup holder/ashtray and locate the small tab on the right-hand side of the unit.
2. Using a flathead screwdriver or other suitable tool, gently press down on the tab to release the retaining clip.
3. While holding down the tab, pull the cup holder/ashtray unit towards you to release it from the center console.
4. Once the unit is free, disconnect any wiring harnesses or light bulbs attached to it, if applicable.

To reinstall the cup holder/ashtray, simply reverse these steps, making sure the retaining clip snaps back into place when reinserting the unit into the center console.

REMOVAL
1. Disconnect and isolate the battery negative cable. 2. Remove the four screws located inside the storage bin. 3. Remove the two screws located under the cup holder lining. 4. Disconnect the electrical connectors. 5. Remove the center console from the vehicle.

Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation

1. Position the seats as needed to remove the console.

1. Disconnect the battery. For additional information, refer to Section 414-01 .

1. Remove the floor console storage bin.
   1. Remove the 3 screws and the armrest.
   1. Remove the floor console storage bin screw.
   1. Remove the pin-type retainer.
   • Disonnect the electrical connectors.

1. Remove the floor console front finish panel.
   • Pull upward from the front of the trim panel to release the retainers.
   • Disconnect the electrical connectors.

1. Remove the floor console center finish panel.

1. If necessary, remove the 2 screws and the floor console cup holder.

1. Remove the 2 floor console front screws.

1. Remove the 3 floor console rear screws.
   • To install, tighten to 4 Nm (35 lb-in).

1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
   • Disconnect the electrical connector.
   • To install, tighten to 8 Nm (71 lb-in ).

1. To install, reverse the removal procedure.

1. Ashtray/cup holder removal - YouTube

   ? 2:39
   www.youtube.com/watch?v=-EFagPT_2js
   Mar 9, 2015 - Uploaded by wonnieboy
   2005 crown vic ashtray/cup holder removal. I broke my face cover cause I didn't knw how to remove it .I ...

Hi Melissa, I'm glad to help, here is the instruction below I said I'd send. Have an awesome day.


23 - Body/Interior/CONSOLE, Floor, Front/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure 1. Remove shift bezel. (Refer to 23 - Body/Interior/BEZEL, Shifter - Removal) .
2. Remove transmission range indicator surround bezel Figure 1.
3. Remove two screws attaching front floor console to the lower instrument panel Figure 2. 4. Open cup holder and remove two attaching screws to bottom of cup holder. 5. Open bin and remove two attaching screws to bottom of bin. 6. Remove front floor console sidewall attaching screws, three per side. 7. Raise front floor console and disconnect wiring harness. 8. Remove front floor console from vehicle.
Figure 1 - TRANSMISSION RANGE INDICATOR SURROUND BEZEL 1 - INSTRUMENT PANEL 2 - AUTOSTICK SHIFTER ASSEMBLY 3 - TRACTION CONTROL SWITCH 4 - TRANSMISSION RANGE INDICTOR SURROUND BEZEL 5 - KNOB SET SCREW 6 - SHIFTER KNOB 7 - FLOOR SHIFT BEZEL 8 - WIRE CONNECTOR 9 - INSTRUMENT PANEL WIRING HARNESS 10 - INSTRUMENT PANEL WIRING CLIP
Figure 2 - FRONT FLOOR CONSOLE 1 - FORWARD CONSOLE CLOSEOUT PANEL 2 - CLOSEOUT PANEL PUSH PIN RETAINER 3 - INSTRUMENT PANEL WIRING 4 - FLOOR CONSOLE BASE 5 - FRONT FLOOR CONSOLE ATTACHING SCREWS TO LOWER INSTRUMENT PANE AND BASE 6 - FRONT FLOOR CONSOLE WIRING CONNECTOR 7 - FRONT FLOOR CONSOLE 8 - ATTACHING L-BRACKETS

Hi Ken, I'm glad to help! Ken I have removed so many of the center consoles on Intrepids, heck I can do it in my sleep. I'm not sure how far you have gotten removing it. But there are some hidden screws under the rear cup holder. Pull the rear seat cup holder out and there is one in the very front and 2 down inside the slot. Those are the only ones you need to remove the other screws simply hold the cup holder in. The rest of the removal is very easy. Hope this helps and have an awesome day Ken!

I assume you mean the one that flips up in the center console?

If so, there are three likely issues.

1) did you slide out the retainer from the upper screw? the top screw had a cover that had to be pried off. you then took the screw out. Lastly you have to slide out the plastic retainer that the screw went into. It slides out towards the opening.

2) you have to have the cup holder partially open to remove it. the hinged part that folds up is stored in the cavity under the console when closed. you have to open the cup holder and keep pushing until the front of the cup holder lip comes up. Work the cup holder up and down until it comes out.

3) the cup holder is stuck in place due to years of spilled liquid. If you've done the above, then you can either spray soapy water on the creases around the opening and let it set, or you can apply strategic brute force.
Be aware through. if this is the center console cup holder just behind the gear shifter. There are two screws and nothing else to hold it in. Just be carefull....

MY FRONT CONSOLE GLOVE COMPARTMENT NEEDS TO BE REMOVED ON MY 2003 CADILLAC ESCALADE TO GET MY PHONE FELL DOWN THROUGH OPEN CRACK.