Express 1500 bank1 sensor2 location

It is possible it is in the passenger side exhaust manifold.

Forget to write it down?

Generic or Manufacturer?

There are 41 Generic O2 Codes

PO 131--bank 1 sensor 1
PO 137--bank1 sensor 2
PO 143--bank1 sensor 3
PO 151--bank2 sensor 1
PO 157--bank1 sensor2
PO 163--bank2 sensor 3

your truck should have four o2 sensors bank 1 sensor 1 is o2 sensor on cylinder 1 side before cat and bank1 sensor2 two is 02 sensor after cat banks 2 sensor1 is on other side berfore cat and bank2 sensor2 is after cat hope that helps when they read code it should tell you bank1 sensor1 or2 good luck

P0136 = Oxygen Sensor Circuit Malfunction (Bank1, Sensor2)
P0141 = Oxygen Sensor Heater Circuit Malfunction (Bank1, Sensor2)

CHECK WIRING BEFORE REPLACING SENSORS

If 4 cylinder engine, there are only two O2 Sensors - Sensor 1 is on top, Sensor 2 is at the bottom

If 6 cylinder, there are four (4) O2 sensors (Bank1, Sensor2 is on the firewall side of this engine and is referred to as the 'DOWNSTREAM' sensor (the one AFTER the Catalytic Converter)

Bank 1 is at the back of the engine compartment next to the firewall. You'll need to know if you need to change (bank 1 sensor 1), or (bank1 sensor2). Sensor 1 is located in the exhaust system between the rear cylinder head and the catalytic converter. Sensor 2 is after the cat in the exhaust system after the cat.

Its o2 sensor error code.-------

P0141-Bank1 Sensor2- code.--------

The "Sensor located after catalytic converter".This o2 sensor needs to be replaced.-------

this will help.thanks.Helpmech.

P0155: O2 Sensor heater Circuit Malfunction (bank2 ) Sensor 1.

P0141: O2 Sensor heater Circuit Malfunction (bank1 ) Sensor 2.

P0135: O2 Sensor heater Circuit Malfunction (bank1,Sensor1)

P0136: O2 Sensor Circuit Low voltage (bank1) Sensor 2.

P0443 : Evaporative Emission control System Purge control valve.

P1451: Eavporative Control System Canister vent solenoid Circuit Malfunction.

P0161: O2 Sensor Circuit Low voltage (bank2,Sensor2)

P1409: Electronic Vacuum Regulator (EVR) control circuit malfunction.

change the O2 sensors first,Then check the the EGR Vacuum regulator for any Malfunction. Good luck

P0138 - Oxygen Sensor Circuit High Voltage (Bank1, Sensor2)

P0139 - Oxygen Sensor Circuit Slow Response (Bank1, Sensor2)

The Heated Oxygen Sensor (1 or 2) located rear of catalytic converter produces an output signal relative to oxygen storage capacity of catalytic converter. Ho2S 2 signal is less active than signal produced by front oxygen sensor. This code sets when HO2 Sensor voltage is greater than 999 mV for more than 2 minutes (time depends on model. Could be as high as 4 minutes)

Symptoms: There may be no noticeable symptoms except for MIL illumination. Possible high fuel pressure can over rich the system.

Causes: A code P0138 may mean that one or more of the following has happened:
* Faulty O2 sensor
* Short to battery voltage in O2 sensor signal circuit
* High fuel pressure (not as likely)

Here are some potential solutions:
* Replace O2 sensor
* Repair short to battery voltage in o2 sensor signal circuit

Hope helps (remember to rate this answer).

This is a 4 cylinder right? Open the hood and look down between the engine and firewall, this is behind the engine. You will see the exhaust pipe, follow the exhaust pipe up to where it is bolted to the exhaust manifold. You will see the upstream O2 sensor screwed in there, more or less horizontally with wire connector pointed at driver side of car. Now get under the car and find the catalytic converter in the exhaust pipe, a big bulbous thing, the downstream O2 sensor will be after the converter, but before the muffler and will also have an electrical connection.

There are 4 oxy. sensors listed for your truck. they're located as follows
Left exaust before catalytic converter. bank1 sensor1-after cat conv.
bank1 sensor2. right exaust before cat.conv. bank2 sensor1-after cat.
conv. bank2 sensor2. Hope this helps.