2001 aurora secondary air injection needs fixed what is the cossst

here is what i found on p1416.



P1416 Chevrolet
P1416 Chevrolet - Secondary Air Injection System Bank 2
Possible causes
- Faulty Secondary Air Injection (AIR) pump
- Secondary Air Injection check valve bank 2
- Secondary Air Injection (AIR) pump electrical circuit fault
- Blocked Secondary Air Injection (AIR) system

When is the code detected?

The P1416 code is set when no O2 sensor voltage change is detected by the Engine Control Module (ECM).


Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)


P1416 Chevrolet Description
An Secondary Air Injection (AIR) pump is used on this vehicle to lower tail pipe emissions on start-up. The PCM supplies a ground to the AIR pump relay, which energizes the AIR pump. The Powertrain Control Module (PCM) monitors the HO2S voltages to diagnose the AIR system. During the AIR test the PCM activates the AIR pump during closed loop operation. When the AIR is activated, the PCM monitors the HO2S voltages and short term fuel trim values for both banks of the engine. If the AIR system is operating properly, the HO2S voltages should go low and the short term fuel trim should go high.

P0491 Secondary Air Injection System (Bank 1)
P0492 Secondary Air Injection System (Bank 2)
Good luck for you!
OBD2 code reader

P0101 Mass or Volume Air Flow Circuit Range/Performance Problem

P0410 Secondary Air Injection System Malfunction

Read this post on secondary air
Secondary air injection pump trouble code Ricks Free Auto Repair Advice

Why would you change the air pump? Did you test or change the valve/switch,that is giving you the code?

Two of the more common problems with Auroras.
P0442 - There is a small solenoid (about $30.00) mounted near the L.R. wheel that will fix this.
P0410 - Usually due to leaking Air Injection Valves. These are about 2" square, one near the passenger side firewall, the other near the drivers side radiator. They cost about $200.00/ea. most people just leave it go as it does not effect performance.

Basically the secondary Air Injection Reactor system (AIR) forces frech air into the exhaust system to reduce HC and CO emissions. Thats why your failing its not doing its job.I'm not sure if you have a electric or belt driven pump ,or do you have the Pulse air system that uses natural pulses from the exhaust topull air into the exhaust system.
Let me know which system you have and I'll give you the testing procedure. This is a fairly easy fix.

1997 BMW 328I 2.8L Customer Concern: MIL is on with trouble codes P1421 and P1423, for incorrect secondary airflow on both cylinder banks. Tests/Procedures: 1. Perform a functional test of the Air Injection Reaction (AIR) system. Tee a vacuum gauge into the vacuum hose attached to the diverter valve, located on the cylinder head towards the front of the engine.

2. Allow the vehicle to sit over night. Start the engine (cold) while monitoring the amount of vacuum on the gauge at startup. At temperatures from -10 to 40 degrees Celsius, there should be at least 17 inches of vacuum. At the same time, the AIR pump should run and pump a large volume of air into the exhaust. Potential Causes: A.I.R. Pump
Air Pump Relay
Restricted Cylinder Head
Diverter Valve
Tech Tips: These codes are related to a problem detected in the Secondary Air Injection system. Scan tools with BMW software include a feature to command the AIR pump on and off. The pattern failures for these codes are the AIR pumps due to leaks in the diverter valve and moisture or condensation in the AIR pump.

Possible fix but not all items. Just areas to look at:
Confirmed Fix - A.I.R. Pump - A.I.R. Diverter - A.I.R. Pump, Air Injection Reaction Diverter (AIRD) Valve - Air Injection Reaction Diverter (AIRD) Valve - Check Valve, Secondary Air Pump - Diverter Valve Vacuum Lines

check the pump it self they fill up with water and the motor goes bad prob needs new motor and then change fuse under hood

please rate me solved...thanks

DTC P0411/16795: SECONDARY AIR SYSTEM - INCORRECT FLOW DETECTED
Test Requirements
Ensure all fuses are okay, battery voltage is at least 11.5 volts, all electrical accessories are off, A/C is off.
Ensure engine is mechanically sound.
Test Procedure

NOTE
Secondary air system is activated by ECM and blows air into exhaust pipe
upstream of catalytic converter for 100 seconds during a cold start, 41-91°F (5-
33°C). Engine must be cold to perform following test procedure.

1. Ensure fuse and secondary fuse (secondary fuse is 40 amp and is located in fuse holder on top of battery)
are okay. Check hoses and components of Secondary Air Injection System, for damage, loose fit and
improper installation, check vacuum hoses for Secondary Air Injection System. Repair as necessary.
Erase DTC memory. Verify repair. If DTC does not reset, test is complete. Perform ECM relearn
procedure. See TEST DRIVE RELEARN PROCEDURE .
2. Remove engine cover. Disconnect pressure hose from Secondary Air Pump Motor (V101), by pressing
buttons on hose connector. See Fig. 33 . Using scan tool, check Secondary Air Pump Motor (V101) in
scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See OUTPUT
DIAGNOSTIC TEST MODE .
3. Secondary Air Pump Motor (V101) should run in intervals and air should exit pump at hose connection.
If Secondary Air Pump Motor (V101) is okay, go to step 7 . If motor runs and no air exits secondary air
pump motor, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE . If
secondary air pump motor does not run, go to next step.
4. Disconnect Secondary Air Pump Motor (V101) harness connector, install LED test light at secondary air
pump harness connector terminals. Turn ignition on. Using scan tool, activate Secondary Air Pump Motor
(V101) in scan tool Output Diagnostic Test Mode (Secondary Air Pump Relay activation mode). See
OUTPUT DIAGNOSTIC TEST MODE . LED test light at Secondary Air Pump Motor (V101) harness
connector should flash. If LED test light at Secondary Air Pump Motor (V101) harness connector does
not flash, go to next step. If LED test light at Secondary Air Pump Motor (V101) harness connector
flashes, replace faulty Secondary Air Pump Motor (V101). Erase DTC memory. Verify repair. Test is
complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
5. Using DVOM check resistance of Secondary Air Pump Motor (V101) wiring. See appropriate WIRING
DIAGRAM under ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS. Resistance should
be a maximum of 1.5 ohms for each reading. Check wiring for short circuit to one another in Secondary
Air Pump Motor (N101) harness connector. Repair as necessary. Erase DTC memory. Verify repair. Test
is complete. Perform ECM relearn procedure.
Secondary Air Pump Motor (N101) wiring is okay, go to next step.
6. Check Secondary Air Pump Relay (J299) and Secondary Air Pump Relay (J299) wiring. See DTC
P0418/16802: SECONDARY AIR PUMP RELAY (J299), MALFUNCTION . Repair or replace as
necessary. Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure. See
TEST DRIVE RELEARN PROCEDURE .
7. Disconnect vacuum hose from Secondary Air Injection Valve (N112) and disconnect pressure hose from
secondary air pump motor, press buttons on pressure hose connector to disconnect pressure hose. See Fig.
34 . Blow lightly into disconnected pressure hose, Combi-Valve should be closed. Connect hand vacuum
pump to disconnected vacuum hose and apply vacuum to Combi-Valve, Combi-Valve should open. If
Combi-Valve opens when vacuum is applied, Combi-Valve is okay. Go to next step. If Combi-Valve
does not open when vacuum is applied, replace faulty Combi-Valve. Erase DTC memory. Verify repair.
Test is complete. Perform ECM relearn procedure. See TEST DRIVE RELEARN PROCEDURE .
8. Check Secondary Air Injection Valve (N112). See DTC P0412/16796: SECONDARY AIR
INJECTION VALVE (N112), ELECTRICAL CIRCUIT MALFUNCTION . Repair as necessary.
Erase DTC memory. Verify repair. Test is complete. Perform ECM relearn procedure.
NOTE: Do not use compressed air to check Combi-Valve.
2000 Volkswagen Passat GLS
2000 ENGINE PERFORMANCE Self-Diagnostics - 1.8L Turbo