I have a 98 hombre 2.2 Manuel I changed the ignition tumbler cause I had no key a lock Smith did it it will start run for about 2 second and shut off. If you wait a few minutes it will start again but shuts off again It has good fuel pressure and a new fuel filter but I can't figure it oit

I WOULD GO AND GET NEW IGNITION SWITCH THEY TIEWAPPED OLD KID? YA I WOULD SAY START BY REPLACING SWITCH THE RIGHT WAY. THEN IS PROBLUM IS FIXED AND U WANT ONE KEY FOR ALL GO TO A LOCK SMITH SO HE CAN MACH UP TUMBLERS IN SIDE LOCK SO ONE KEY WORKS ALL

your tumblers inside of switch is off not matching your key cut ,this a command prob .you need to have switch replaced ,or have lock smith change tumblers

I would replace the ignition cylinder. the tumbler are wearing funny and this is causing the key to not turn or get stuck . I believe you have a pass key system on your car too . so after the cylinder is replace or rebuild you may need to do a relearn with the new lock cylinder. Not sure if you can rebuild the key cylinder and if a lock smith would have the right tumbler codes . but i know for sure if you buy the lock cylinder from a dealership they can code the tumbler to match the original key

get an expert lock smith to recut you a new key the tumblers mite have moved or just change the ignition switch

need more info does the key work in the door i am in the process of elimination thanks This is asked to give you the best possible repair

the tumblers have worn out and not engaeing properly. Repair consists of removeing the ignition switch assembly and installiing a new one. Since it has jammed, mostly a tumbler or two may have broken off in the cylinder houseing also.

if tapping it doesnt work. hit it hard for a few minutes then try to turn it forward and back both then repeat.  I had a tow truck come to tow me and he started banging on mine.  I said i already did that while waiting for you and he said you will see.  he kept doing it and a few minutes later i looked like a ********.  He told me the pins were sticking and a lock smith could take the first 2 pins out for me. 

for 98 contour issue. TSB 98-21-14 not covered by warranty

This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE

1. Verify customer concern.
2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).
   
   
   Figure 1 - Article 98-21-14
   
   NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
   
6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
   
7. Program PATS keys using one of the two following methods:
   

(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:

• 2/2/98 Kansas City (Contour/Mystique)
• 2/16/98 Mexico (Contour/Mystique)
• All 1999 Cougars

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PCM
   • Enter Security Access (10 minute delay)
   • Ignition Key-Code-Erase
2. Disconnect Data Link Connector (DLC).
3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
5. Verify the vehicle will now start using both keys.
   

(2) For Contours/Mystiques with Stand Alone PATS and built before:

• 2/2/98 Kansas City
• 2/16/98 Mexico

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PATS
   • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
2. Disconnect DLC.
3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
   • Part Number suffix will match center character in key code
   • Logo on key is Ford for Contour models
   • Logo on key is Mercury for Mystique and Cougar models
   
   

PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar)

You might not need a tumble, the sys is controled by the key, and transponder, and the ecm. Most auto locks smiths can come out and check the system, might just need a key re-programed

this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14

• IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED

Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE

1. Verify customer concern.
2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).
   
   
   Figure 1 - Article 98-21-14
   
   NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
   
6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
   
7. Program PATS keys using one of the two following methods:
   

(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:

• 2/2/98 Kansas City (Contour/Mystique)
• 2/16/98 Mexico (Contour/Mystique)
• All 1999 Cougars

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PCM
   • Enter Security Access (10 minute delay)
   • Ignition Key-Code-Erase
2. Disconnect Data Link Connector (DLC).
3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
5. Verify the vehicle will now start using both keys.
   

(2) For Contours/Mystiques with Stand Alone PATS and built before:

• 2/2/98 Kansas City
• 2/16/98 Mexico

Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:

1. From NGS menu, select:
   • Service Bay Functions
   • PATS
   • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
2. Disconnect DLC.
3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
   • Part Number suffix will match center character in key code
   • Logo on key is Ford for Contour models
   • Logo on key is Mercury for Mystique and Cougar models
   
   

PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar