What causes obd code u110c - Cars & Trucks

With all those codes, you need a good auto-electrician with a $5,000 pro grade scan tool computer. Most of this is Body Control Module issues.

U0141 Lost Communication With Body Control Module "A"

https://www.obd-codes.com > u0141
Code U0141 pertains to the BCM "A" or the wiring to the BCM from the engine control module (ECM). The code, depending on the year, make and model of the ...

U1403 - Implausible Fuel Level Signal Received - Engine ...https://www.engine-codes.com > u1403'What is U1403 code meaning? ... The Fuel Level Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the fuel level message to the ...

U110C CHRYSLER Code - Lost Fuel Level Messagehttps://www.engine-codes.com > u110c_chrysler'What is U110C CHRYSLER code meaning? ... The Fuel Level Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the fuel level ...

U110E CHRYSLER Code - Lost Ambient Temperature Messagehttps://www.engine-codes.com > u110e_chrysler'What is U110E CHRYSLER code meaning? ... The Ambient Temperature Sensor signal is a direct input to the Body Control Module (BCM). The BCM transmits the ambient ...

Code U0100 stands for Lost Communication with ECM/PCM. The powertrain control module (PCM) is the computer responsible for engine management. Like the other computers (known as modules) onboard your vehicle, the PCM communicates over a bus.U0100 - OBD II Trouble Code: Lost Communication with ECM ...

U110C-NO FUEL LEVEL BUS MESSAGE RECEIVED
U0141-LOST COMMUNICATION WITH FRONT CONTROL MODULE
U1403-IMPLAUSIBLE FUEL LEVEL SIGNAL
U110E-LOST AMBIENT TEMPERATURE MESSAGE

Pull the negative off of your battery for 10 minutes and allow the cars CPU to reboot.

Hi Anonymous, Im glad to help!

The U110C is a BUS Message and usually has to do with both PCM and BCM, because its a lose of BUS Signal between the PCM and the BCM.

FIRST THING TO TRY:
The first thing I would try is remove the negative battery cable for 20 seconds then replace it. NEXT: Start the engine several times then let idle for 10 to 20 minutes then start it several more times and if the code doesn't return and the check engine light stays out, simple drive it for awhile like you normally would. If the code come right back, below is some common problems.

COMMON CAUSES of U110C:
(1) Communication with BCM is lost / See if you can communicate with the BCM.
(2) PCI Bus Circuit open between PCM and BCM / Check the positive and negative bus signal at both the PCM and BCM.
(3) BCM
(4) PCM
(5) Fuel Level Bus Message is missing

Obviously, all these issues must be tested to see which one is causing the problem. BUT first try the battery cable removal and see what happens.

Let me know the out come and I'll try to help further.
Hope this helps and have an awesome day!

U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored and Set Condition:
U110C-NO FUEL LEVEL BUS MESSAGE
When Monitored: Ignition on.
Set Condition: No fuel level BUS messages received by the PCM for 20 seconds.
POSSIBLE CAUSES
DTC RESET
COMMUNICATE WITH BCM
FUEL LEVEL BUS MESSAGE
PCI BUS CIRCUIT OPEN FROM PCM TO BCM
BCM
TEST ACTION APPLICABILITY
1 NOTE: If a fuel level circuit or performance DTC is set along with P1681,
diagnose the circuit/performance DTC before continuing.
Turn the ignition on.
With the DRBIIIt, erase DTCs.
Start the engine on and off several times. Leave the engine running for at least 20
second each time.
With the DRBIIIt, read DTCs.
Does the DTC reset?
All
Yes ! Go To 2
No ! Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
2 Ignition on, engine not running.
With the DRBIIIt, attempt to communicate with the BCM.
Can communication be established with the BCM?
All
Yes ! Go To 3
No ! Refer to the Communication Category and perform the appropriate
symptom related to no communication with BCM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
3 Turn the ignition on.
Using the DRBIIIt, read the Fuel Level parameter in the PCM.
Does the DRBIIIt display a fuel level value?
All
Yes ! Replace and program the Powertrain Control Module in accordance
with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Go To 4
287
DRIVEABILITY - NGC
TEST ACTION APPLICABILITY
4 Turn the ignition off.
Disconnect the PCM harness connectors.
Disconnect the BCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMINALS
RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the PCI Bus circuit from the BCM harness connector to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes ! Replace BCM in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC.
No ! Repair the PCI Bus circuit between the PCM and the BCM for an
open.
Perform POWERTRAIN VERIFICATION TEST VER - 1 - NGC
__________________

what do these code mean u110c,u0141,u1403,u110e for dodge nitro 07

Code u110c ( no fuel level) Remove the gas cap from the van. Reinstall and make sure to give the gas cap a full 5 to 6 turns. The code set in the system was set by the gas cap not being tightened enough or a faulty fuel cap. If it continues to reset code then replace fuel cap on van. Hope this will help.

First the fault codes,
U110C is No Fuel Level Bus Message
U0155 is No Cluster Bus Message.
Unfortunatly you have to be able to communicate with the instrument cluster with your scanner to diagnoise and I do not think an aftermarket scanner can do this.

you are incorrect on your code read. u0155 is lost comm with IPC, u110c is no fuel read, u0140 lost comm with BCM and can all be fixed with a new BCM.

2005 town and country code U110C this problem?

the security device in the cat that communicates with the key has failed, dealership service will most likely be needed