Question about 2005 GMC Yukon Denali

4 Answers

2005 GMC Yukon Denali - Traction Control issue

I am getting a "traction active" message on my dash board screen. Which is activing my traction control on dry payment when taking off from a stop. I am worried this is going to mess up my transmission. I have read about the wheel speed sensor corroding in areas where salt is used on the roads. This problem just started after we had ice/snow.
Please help. My truck has 50k with expired warranty it is going to cost me $150 just to have it looked at.

Posted by on

  • 1 more comment 
  • iwcsf Feb 06, 2009

    I have a 05 yukon denali and also have a traction active message on the dash. I get a buzzing sound when it activates and the truck fall on its face. I have had it in the shop and had the wheel speed sensors checked and omed out. I don't have a check engine lite. Is there any sort of motor that could be making this happen

  • Anonymous Feb 19, 2009

    Traction Active comes on and the drive train stops until you let off the accerator

  • Bob Golen Dec 03, 2012

    I had the same problem on my 05 Yukon...needed two new wheel bearings and two new speed sensors. Problem fixed.

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Your problem is the front wheel speed sensor. I had the same problem on my 2004 Denali. The GMC dealer felt there was nothing wrong, no codes. I replaced both from wheel sensors (about $75 each on Ebay) and the problem is fixed. The passenger sensor had a crack in it. I saw this solution on a discussion chat. There was a TSB for the 2002 pickup trucks with the same problem. Hope this helps.

Posted on Mar 19, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

The Speed Sensor is the Problem. Not sure where it is on this Model. But, I have Diagnosed this Before on this Model and it Fixed the Problem.

Posted on Jan 22, 2009

  • lionsdistinc
    lionsdistinc Dec 27, 2012

    I've go a 05 Denali.. It will occatioally cut out at stop signs and lights.. It shuts down for about a second or two.. Then reingages. By replacing the front wheel speed sensors, will that cure the problem?

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Tell how to fix speed senors

Posted on Sep 25, 2012

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

How hard is it to change these?

Posted on Jan 15, 2010

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How difficult is it to replace the brake pedal positioning sensor?


How do you know brake pedal positioning sensor needs to be replaced ? Traction light on ? DTC'S - diagnostic trouble code's stored . That's why cruise won't engage . Taking your vehicle to a qualified repair shop an having it diagnosed is what you should do.
Cruise Control Inhibited
The engine control module (ECM) inhibits the cruise control operation when any of the following conditions exist:
• The ECM has not detected a brake pedal activation from the body control module (BCM).
• A Cruise Control System DTC has been set.
• The vehicle speed is less than 40.2 km/h (25 mph).
• The vehicle speed is too high.
• The vehicle is in PARK, REVERSE, NEUTRAL, or 1st gear.
• The engine RPM is too low.
• The engine RPM is too high.
• The system voltage is not between 9-16 volts.
• The Antilock Brake System (ABS)/Traction Control System (TCS) is active for more than 2 seconds.

Do the stop lamps work ?
DTC P0703 Brake Switch Circuit 2
The body control module (BCM) monitors the brake pedal position sensor. When the brake pedal is applied, the BCM detects a predetermined voltage signal. The BCM sends a GMLAN serial data message to the powertrain control module (PCM) indicating the status of the stop lamps.

DTC P1574 Stop Lamp Switch Circuit
The stop lamp switch signal circuit is a direct hardwire input to the throttle actuator control (TAC) module from the body control module (BCM). The TAC module monitors the stop lamp switch signal circuit in order to detect when the brake pedal has been applied. When the brake pedal is pressed, the BCM sends a GMLAN serial data message to the powertrain control module (PCM) indicating that the brake pedal has been applied. The BCM also sends a high voltage signal on the stop lamp switch signal circuit to the TAC module. The TAC module sends a universal asynchronous receiver transmitter (UART) serial data message to the PCM indicating that a brake pedal application has occurred. The PCM will compare the UART serial data message and the GMLAN serial data message in order to confirm that both serial data messages match.

Sep 17, 2018 | 2006 Pontiac G6

1 Answer

What is traction active on 04 escalade?


It would be a good idea to return to where you had the valve replaced and give the mechanic an opportunity to make it right.

Dec 11, 2015 | 2004 Cadillac Escalade

1 Answer

Why does the traction active keep coming on in my 2003 Chevy Tahoe?


to locate and fix the you can take help from service and repair manual which you can get from the given link to save your time and money http://toolsnyou.com/

Dec 07, 2017 | 2003 Chevrolet Tahoe

1 Answer

ABS-traction control check and service


I'll start with the code reader. Most simple readers will only read engine codes. You need a professional scan tool that does everything to access the body computer data.
It could be a wheel sensor which the ABS system uses, or one of the other components in the ABS system.

Jul 06, 2012 | Cars & Trucks

1 Answer

2005 impala traction control active light


Usually caused by a wheel speed sensor on the drive wheels. Check the sensor mounting, wiring, and tone ring for damage.

Nov 16, 2017 | 2005 Chevrolet Impala

1 Answer

MESSAGE CENTRE TC


TC = Traction Active

If your vehicle is equipped with the Traction Control system, this message will stay on a few seconds after the traction system stops limiting wheel spin.

This message will appear when the traction control system is limiting wheel spin. Keep in mind that when the warning lights turn on, a fault code is stored in the ABS control module (in this case). Retrieving, diagnosing, and repairing any ABS system faults will be necessary to keep the light off. A common fault with ABS systems are the wheel speed sensors, stored codes may confirm this.

Hope this helps.

Apr 13, 2011 | 2005 Chevrolet Impala

1 Answer

How do I know when my Traction control is working on my 2010 Touring? We live in Northeastern Ohio and I seem to be sliding alot when I go to stop and I'm not speeding. Thank You!


A good way of testing the traction control is to stop on a slippery road and then take off fast as to spin the wheels there when wheels start to spin the traction should activate and stop the spinning wheels you may hear it kick inand a light on the dash will say trac active or trac on, as far as sliding when stopping this is where the abs would come in,abs anti skid brake system, this system when you are braking would release the sliding or skidding wheel and you would felt it in the brake pedal, good luck, hope this helps.

Jan 08, 2011 | 2010 Hyundai Elantra Touring

1 Answer

In the message board the traction active message appears


This will appear if the tires slip or spin faster than another,but should go off after the slip is done, if the light stays on then have the traction control system checked.

May 14, 2010 | 2002 Chevrolet Impala

1 Answer

Traction active message is coming on what dose this mean?


Your car has what is called "traction Control" when wheel slip is detected by the system it takes control of the brake system and stops the spin, some cars call this Stability Control, if the light is always on then the system has a failed part and is turned off by the control unit.

Mar 08, 2010 | 2004 Chevrolet Impala

1 Answer

2004 escalade service ride control message came on @ 106,000miles


I would take it to the dealer immediately, as it sounds like the traction control is spontaneously being activated

Jan 18, 2018 | 1994 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

6,388 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...