2004 Mazda 6 Logo

Related Topics:

Anonymous Posted on Jul 03, 2017

Should i just bring my 2004 mazda 6 to a mechanic

I changed the alternator and the AT light comes off and on. The rpms rev up high and only wanna shift from 1-3. It didnt have this problem before i changed the alternator. Ive disconnected the battery cables, checked all the wires, tried to reset the computer everything ive found online ive done and just cant figure out whats wrong.. im stumped and everyones advice isnt working. Should I just bring it to the dealership or a mechanic?!

  • Anonymous Dec 16, 2012

    What does escalated by level 3 mean?! Im confused..

×

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Apr 04, 2009

SOURCE: battery warning light comes on

hi i had the problem in the past and it was a loose conection with the wires,

Ad

Anonymous

  • 3533 Answers
  • Posted on Apr 26, 2009

SOURCE: i need to get a manual or book on my mazda 6 sport

if you mean the owners manual try online at www.edmonds.com they have owners manuals for most vehicles

Anonymous

  • 1 Answer
  • Posted on May 07, 2009

SOURCE: Changing the bulb for a headlight

I guess you refer to the dipped beam headlamp?
If the light is a normal one, not the fancy expensive bright lamp, bluish colour light emitted you should be able to reach it throgh the wheelarch after removing part of the plastic trim.
The cover rotates and can be easily removed.
The there is the usual wire spring loop that hold the lamp in.
The lamp in mine was a standard H1 single filament bulb.
Took about 20 minutes to replace in semi darkness with the aid of a wind-up torch!

Hope this helps.

Paul H.

Anonymous

  • 710 Answers
  • Posted on May 09, 2009

SOURCE: 2004 mazda 6 reverse lights dont come on when i

COULD BE THE REVERSE LIGHT SWITCH INSIDE THE SHIFTER. GOOD LUCK. THANKS FOR USING FIX-YA.

Anonymous

  • 13 Answers
  • Posted on May 10, 2009

SOURCE: 1993 mazda mx6 transmission is not slipping, but will not shift into higher gears. Will run at high RPM's and not shift up. Any suggestions on what it might be.. Mechanical, electrical, fluid change,

sounds like a shift solenoid in the trans.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Why dose fuse to the TCM keep blowing along with one to fule rail

the out put of the alternator is wrong at 18.9 volts
it should be at 14.5 to 14.8volts maximum
the high voltage will be making high current flow and that will blow fuses
have the alternator bench tested and check the regulator as well as the regulator controls the voltage.
1helpful
1answer

How to get 2004 mazda 6 out of safety/hold mode

I would double check everything and make sure you didn't knock a connector loose or pinch a wire or possibly break/damage a nearby sensor. Otherwise try disconnecting BOTH battery cables and touch them together, that will discharge any capacitors that could store corrupt data in the pcm.
0helpful
1answer

AT light came on after changing the alternator

Go back and check wiring there maybe something that got unpluged while doing the repair or put a scan tool on it to see if it will pull up a code some auto parts stores will do this check for free.
0helpful
1answer
0helpful
1answer
5helpful
1answer

2002 mazda protege5 auto battery light coming on

I'm guessing that you've tested the actual current output of the alternator then. I'm assuming that the output is between 13-14Volts at the battery when the car is running... If it's too low, then it's not charging your battery at all, too high, and it's frying your battery.... Another thing that can cause this is if you have a short in your electrical system.. that, however, will be difficult to narrow down...
0helpful
1answer

Lights pulse high and low

Check your battery cables and have someone check your alternator output voltage, it should be 14v when the car is running. Check that the belt to the alternator is not loose.
0helpful
1answer

Won't go higher then 2nd gear, AT and Check Engine light have come on.

seems to be a shot gear pack or a faulty tcm that is not commanding the shift solenoids correctly. i would drop the pan and inspect the fluid. if you notice any metal fragments on the bottom of the transmission pan, this will confirm gear failure. you will need to rebuild in this case.
Not finding what you are looking for?

93 views

Ask a Question

Usually answered in minutes!

Top Mazda Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...