How do i remove rear bench seat from 08 lancer es

Question edited for FULL 'year MAKER model'.
Question moved from Spanish car maker 'Seat' pronounced 'see-at' to correct category.

See videos and articles

https://www.google.com/search?q=1990+Mitsubishi+Montero.+remove+the+rear+bench+seat

..

check the bottom front side of bench seat.
look to see if pull out tabs '
lift.
see
https://www.autoinstruct.com.au/manufacturer/holden/ve-commodore/removing-rear-seat/
for full tutorial

You must remove the seat cushion bottom to access the bolts for the seat back.

Remove the LOWER seat in the rear, u will see ur fuel tank and the fuel float connector!
First disconnect the ( - ) pole of battery to, remove the screws holding the fuel float/pump, remove the rubber seals, and u can pull out the pump assembly!

it's in the fuel tank, you really don't have to replace it unless you have problem with fuel pump.


to acess the fuel pump you need to take the rear seat off

I don't think you can. I owned a 07 EL 8 passenger, now i own a 08 EL 7 passenger and the floor hooks for the seats are located differently (the 8 passenger has an extra hook, if I remember correctly), so i don't think its possible, look at your manual and only shows how to move the seats.

REMOVAL & INSTALLATION

1. Clamp the seat belts to keep them from retracting.
2. Locate and disconnect seat wiring at the connector(s).
3. Move front seats forward or back for access to the hold down hardware.
4. Put the rear seats in the stowed position.
5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
6. Remove the hardware securing the seat.
7. On split bench models, lift the center seat upward to clear attachment stud
8. Remove the seat from the vehicle.

NOTE Do NOT activate the track adjusters once the fastening hardware is removed.

1. Installation is the reverse of removal.

Fig. Disconnect the wiring from under the seat




Fig. Seat track mounting hardware locations-typical




Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram




Fig. Split bench seat assembly-Ram




Fig. Bucket seat mounting components-Durango shown




Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal

1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
   

1. Slide the bench seat forward to the center row seating position.
   

1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.
   
   
   
   
   

1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.
   
   
   
   
   

1. Remove the bench seat from the vehicle through the body side door opening.
   

the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

Seat —Third Row Bench Removal
CAUTION: Removal of the third row bench seat requires more than one technician.

1. Remove the second row seats. For additional information, refer to Seat—Second Row .

1. Remove the floor mats.

1. Lock the seat cushion in the upright position.
   1. Lift the handle to release the cushion.
   1. Lock the seat cushion in the upright position.

1. Move the third row bench seat to the second row position.
   • Lift the seat track release handle.

1. Remove the two bolt covers.

1. Remove the two seat track front bolts.

1. Remove the four seat track rear bolts.
   1. Position the rear seat cushion floor cover aside.
   1. Remove the four seat track rear bolts.

1. Remove the third row bench seat.

The only way to remove this is to unbolt it from the sliding rails. I do believe it would still leave some parts in the rails. This seat was designed to only slide forward and not be removed. If you insist on removing it, then you must unbolt it from the sliding rails...